1.5 Zoll OLED-Anzeige 128x128 - WEA128128A

1,5 Zoll OLED-Anzeige 128x128 COG+PCB

Modellnummer WEA128128A

►1,5" OLED
►Typ: Grafik
►Bauweise: COG+PCB
►128 x 128 Punktmatrix
►IC：SSD1327
►3,5-V/5-V-Stromversorgung
►1/128 duty
►Schnittstelle: SPI, optional I2C
►die Farbe des Displays: Weiß / Gelb
►Unterstützt Grauskala

PDF-Download

Democode Zu Anfrage hinzufügen

Zurück Zurück zur Liste Weiter

Beschreibung

Zeichnung

OLED 1.5 inch,1.5 OLED Display, 1.5 inch OLED Display, 1.5 inch OLED Module - WEA128128A

Data source ref: WEA128128AWAP3N00000

Technische Daten

mechanische Daten

Artikel	Ausmaß	Einheit
Punktmatrix	128 x 128 Dots	－
Abmaße der modul	34,2 x 45,5 x 3,16	mm
Aktiver Bereich	26,86 x 26,86	mm
Punktgröße	0,185 x 0,185	mm
Punktabstand	0,210 x 0,210	mm
der Anzeigemodus	Passive Matrix
die Farbe des Displays	Monochromes
Drive Duty	1/128 Duty
Grauskala	4 bits
IC	SSD1327
Schnittstelle	4-Wire SPI / I2C
Größe	1,5 Zoll

Absolute Grenzwerte

Parameter	Symbol	Mindestwert	Maximalwert	Einheit
Supply Voltage for Logic	VCC	1,65	5,5	V
Betriebstemperatur	TOP	-40	+80	°C
Lagertemperatur	TSTG	-40	+85	°C

elektronische Eingenschaften

Artikel	Symbol	Bedingung	Mindestwert	typischer Wert	Maximalwert	Einheit
Supply Voltage for Logic(3V/5V)	VCC	－	2,8	3,3	5,2	V
Input High Volt.	VIH	－	0,8×VCC	－	VCC	V
Input Low Volt.	VIL	－	0	－	0,2×VCC	V
Output High Volt.	VOH	－	0,9×VCC	－	VCC	V
Output Low Volt.	VOL	－	0	－	0.1×VCC	V
50% Check Board operating Current	ICC	VCC=3,3V	－	160	320	mA

Schnittstelle Pin-Funktion

No.	Symbol	Beschreibung
1	GND	This is a ground pin.
2	VCC	Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3	D0	These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
4	D1
5	RES#	This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation.
6	D/C#	This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
7	CS#	This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).