Startseite Produkte OLED-Anzeige Grafik-OLED-Anzeigen WEO128128A

1,5 128x128 SSD1327 OLED-Anzeige

Modellnummer WEO128128A

►Typ: Grafik
►Bauweise: COG
►Größe: 1,5" OLED
►128x128 Punktmatrix
►IC:SSD1327
►3-V-Stromversorgung
►1/128 duty
►Schnittstelle: 6800, 8080, SPI, I2C
►die Farbe des Displays: Weiß / Gelb
►Unterstützt Grauskala
►Andere in der nachstehenden Tabelle verfügbare FPC-Optionen

Beschreibung

Das Winstar WEO128128A ist ein Passivmatrix-OLED-Display mit einer Auflösung von 128x128 Pixeln, Die Diagonale misst 1,5 Zoll. Es hat eine Modulgröße von 33,8 x 36,5 mm und eine AA-Größe von 26,86 x 26,83 mm. Das Modul ist mit dem SSD1327 Controller ausgestattet und unterstützt 6800/8080 8-Bit-Parallel-, I2C und 4-Draht-SPI-Seriell- Schnittstelle. Die Versorgungsspannung beträgt 3V. Das WEO128128A ist ein 1,5" OLED-Display mit COG-Struktur, das extrem dünn ist und keine Hintergrundbeleuchtung benötigt (selbstleuchtend). Es ist leicht und sparsam im Verbrauch. Dieses Modul eignet sich für tragbare Geräte, Messgeräte, IoT usw.

Das WEO128128A kann bei Temperaturen von -40 ℃ bis + 80 ℃ betrieben werden; die Lagertemperatur liegt zwischen -40 ° C und + 80 ° C. Im Folgenden finden Sie eine kurze Spezifikation als Referenz. Für weitere Informationen wenden Sie sich bitte an unseren Vertriebsmitarbeiter.


   FPC-Optionen

 

Zeichnung

OLED Display 128x128, 128x128 OLED Display, 128x128 pixel OLED Module - WEO128128A

 

Data source ref: WEO128128ALAP3N00000

Technische Daten

mechanische Daten

Artikel Ausmaß Einheit
Punktmatrix 128 x 128 Dots
Abmaße der modul 33.80 x 36.50 x 2.05 mm
Aktiver Bereich 26.86 x 26.86 mm
Punktgröße 0.185 x 0.185 mm
Punktabstand 0.210 x 0.210 mm
der Anzeigemodus Passive Matrix
die Farbe des Displays Monochrome
Drive Duty 1/128Duty
Gray-Scale 4 bits
IC SSD1327
Schnittstelle 6800,8080,SPI,I2C
Größe 1.5 Zoll

Absolute Grenzwerte

Parameter Symbol Mindestwert Maximalwert Einheit
Low voltage power supply, power supply for I/O pins VCI -0,3 4,0 V
Supply Voltage for Logic VDD -0,5 2,75 V
Supply Voltage for Display VCC -0,5 19,0 V
Betriebstemperatur TOP -40 +80 °C
Lagertemperatur TSTG -40 +85 °C

elektronische Eingenschaften

Artikel Symbol Bedingung Mindestwert typischer Wert Maximalwert Einheit
Low voltage power supply, power supply for I/O pins VCI   2,8 3 3,3 V
Supply Voltage for Display VCC 14 14,5 15 V
Supply Voltage for Logic VDD 2,4 2,6 V
High Level Input VIH 0,8×VCI VCI V
Low Level Input VIL 0 0,2×VCI V
High Level Output VOH 0.9×VCI VCI V
Low Level Output VOL 0 0,1×VCI V
50% Check Board operating Current VCC =14,5V 24 36 mA

Schnittstelle Pin-Funktion

No. Symbol Beschreibung
1 VSS Ground pin. It must be connected to external ground.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.
4 VCI Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.
5 VDD Power supply pin for core logic operation.
VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated
Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances.
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select.
Bus Interface selection
BS[2:1] Interface
00 4 line SPI
01 I2C
11 8-bit 8080 parallel
10 8-bit 6800 parallel
Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
7 BS2
8 VSS Ground pin. It must be connected to external ground.
9 IREF This pin is the segment output current reference pin
10 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
11 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
12 D/C This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
13 W/R# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.

FPC-Optionen:

Bild FPC Length PIN Pitch ZIF FPC or HOTBAR FPC Schnittstelle FPC No. Create Date
FPC2050002411XXXXX03_WEO128128ALAP3N00000 25.05 24 0.5 ZIF 6800,8080,SPI,I2C FPC2050002411XXXXX03 20150901
FPC2050002411XXXXX12_WEO128128AWAP3N00002 41 24 0.5 ZIF 6800,8080,4-Wire SPI,I2C FPC2050002411XXXXX12 20200116

Ähnliche Produkte

go top
close

Wir schätzen Ihre Privatsphäre

Durch Klicken auf „Alle Cookies zulassen“ stimmen Sie der Speicherung von Cookies auf Ihrem Gerät zu, um die Navigation auf der Website zu verbessern, die Nutzung der Website zu analysieren und unsere Marketing- und Leistungsbemühungen zu unterstützen. Weitere Informationen zu diesem Thema finden Sie in unserer Richtlinie. Datenschutzrichtlinie

Wir schätzen Ihre Privatsphäre

Winstar und bestimmte Drittparteien verwenden Cookies auf www.winstar.com.tw. Die Einzelheiten zu den Arten von Cookies, ihrem Zweck und den beteiligten Drittparteien sind unten sowie in unserer Cookie-Richtlinie beschrieben. Klicken Sie auf „Alle zulassen“, um unserer Verwendung von Cookies zuzustimmen und die bestmögliche Erfahrung auf unseren Websites zu erzielen. Sie können auch Ihre Präferenzen festlegen oder Cookies ablehnen (mit Ausnahme der unbedingt erforderlichen Cookies).

Einwilligungspräferenzen verwalten

Immer aktiv
Notwendige Cookies

Diese Cookies sind unerlässlich, um Ihnen das Navigieren auf der Website zu ermöglichen und ihre Funktionen zu nutzen, wie z. B. das Festlegen Ihrer Datenschutzpräferenzen, das Einloggen oder das Ausfüllen von Formularen.

Analyse-Cookies

Diese Cookies, auch als „Statistik-Cookies“ bekannt, sammeln Informationen darüber, wie Sie eine Website nutzen, z. B. welche Seiten Sie besucht und auf welche Links Sie geklickt haben. Siehe Details.