首页 产品介绍 OLED显示屏 图形 OLED 显示屏 WEO128128A

1.5寸COG点阵图形OLED显示模块128*128

型号 WEO128128A

►类型:点阵图形
►结构:COG
►尺寸:1.5寸
►128x128点阵
►IC:SSD1327
►3V电源电压
►1/128 duty
►接口: 6800, 8080, SPI, I2C
►发光颜色: 白色 / 黄色
►支持灰度
►其它FPC选项请参阅最下方表格说明

产品叙述

WEO128128A 是一款1.5吋单色被动式OLED显示器模块,分辨率为128x128 pixels。WEO128128A内建SSD1327 controller控制器, 支持多种传输接口: 6800 8-bite, 8080 8-bit 并行接口, I2C 与4线SPI串行接口。WEO128128A的模块尺寸为33.8 x 36.5 mm,AA区尺寸26.86 x 26.83 mm, 3V驱动。WEO128128A为COG结构的OLED显示器模块,为有机自发光,无须背光源,因此模块轻薄且低耗电流,此款WEO128128A模块非常适合手持式产品、量测仪器、物联网装置、工控设备等等。

此模块的工作温度是-40℃至+80℃,储存温度-40℃至+80℃,如有产品需求或是需要更详细信息请与我们联系。


     可选 FPC

 

规格图

OLED Display 128x128, 128x128 OLED Display, 128x128 pixel OLED Module - WEO128128A

 

Data source ref: WEO128128ALAP3N00000

产品规格

规格说明

项目 尺寸 单位
点阵 128 x 128 Dots
模块尺寸 33.80 x 36.50 x 2.05 mm
有效区域 26.86 x 26.86 mm
像素大小 0.185 x 0.185 mm
像素间距 0.210 x 0.210 mm
显示模式 被动矩阵
发光颜色 单色
驱动方式 1/128Duty
灰度 4 bits
IC SSD1327
接口 6800,8080,SPI,I2C
尺寸 1.5 寸

最大绝对额定

参数 符号 最小值 最大值 单位
低压电源,输入/输出 Pin 电源 VCI -0.3 4.0 V
逻辑电源电压 VDD -0.5 2.75 V
显示电源电压 VCC -0.5 19.0 V
工作温度 TOP -40 +80 °C
储存温度 TSTG -40 +85 °C

电气特性

项目 符号 条件 最小值 典型值 最大值 单位
低压电源,输入/输出 Pin 电源 VCI   2.8 3 3.3 V
显示电源电压 VCC 14 14.5 15 V
逻辑电源电压 VDD 2.4 2.6 V
输入高准位 VIH 0.8×VCI VCI V
输入低准位 VIL 0 0.2×VCI V
输出高准位 VOH 0.9×VCI VCI V
输出低准位 VOL 0 0.1×VCI V
50%显示画面耗电流 VCC =14.5V 24 36 mA

Pin功能定义

No. 符号 功能说明
1 VSS Ground pin. It must be connected to external ground.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.
4 VCI Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.
5 VDD Power supply pin for core logic operation.
VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated
Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances.
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select.
Bus Interface selection
BS[2:1] Interface
00 4 line SPI
01 I2C
11 8-bit 8080 parallel
10 8-bit 6800 parallel
Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
7 BS2
8 VSS Ground pin. It must be connected to external ground.
9 IREF This pin is the segment output current reference pin
10 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
11 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
12 D/C This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
13 W/R# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.

可选FPC:

FPC 长度 PIN Pitch ZIF FPC / HOTBAR FPC 接口 FPC No. 建立日期
FPC2050002411XXXXX03_WEO128128ALAP3N00000 25.05 24 0.5 ZIF 6800,8080,SPI,I2C FPC2050002411XXXXX03 20150901
FPC2050002411XXXXX12_WEO128128AWAP3N00002 41 24 0.5 ZIF 6800,8080,4-Wire SPI,I2C FPC2050002411XXXXX12 20200116

推荐产品

go top
close

我们重视您的隐私

通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。

我们重视您的隐私

Winstar 及部分第三方在 www.winstar.com.tw 上使用 cookies。关于 cookie 的种类、用途及相关第三方的详细信息,请参见下文及我们的《Cookie 政策》。请点击“允许全部”来同意我们使用 cookies,以确保您在我们网站上获得最佳体验。您也可以设置您的偏好或拒绝 cookies(必要的 cookies 除外)。

管理同意声明

永久启用
必要的 Cookie

这些 Cookie 是必不可少的,以便让您在浏览网站并使用其功能上有更好地体验,例如设置您的隐私偏好、登录或填写窗体。

分析 Cookie

这些也被称为「统计cookie」,用于收集您使用网站的信息,例如您访问了哪些页面以及点击了哪些连结。查看详细信息