1.5 inç SSD1327 OLED Ekran 128x128 - WEO128128A

1.5 inç SSD1327 OLED Ekran 128x128

Model No. WEO128128A

►Türü : Grafik
►Yapı : COG
►Boyut : 1.5 inç
►128x128 dot matrisi
►IC：SSD1327
►3V güç sağlayıcı
►1/128 görev
►Ara yüz : 6800, 8080, SPI, I2C
►OLED Rengi: Beyaz / Sarı
►Support Grayscale
►Other FPC options available in below table

PDF İndir

DEMO CODE Sorguya ekle

Önceki Listeye geri dön Sonraki

Açıklama

FPC Seçenekleri

ÇIZIM

OLED Display 128x128, 128x128 OLED Display, 128x128 pixel OLED Module - WEO128128A

Data source ref: WEO128128ALAP3N00000

AYRINTILAR

Mekanik Veri

Kalem	Dimension	Birim
Nokta Matrisi	128 x 128 Dots	－
Modül ölçüleri	33.80 x 36.50 x 2.05	mm
Aktif alan	26.86 x 26.86	mm
Nokta boyutu	0.185 x 0.185	mm
Nokta sıklığı	0.210 x 0.210	mm
Display Mode	Pasif Matrisli
OLED Rengi	Monokrom
Drive Duty	1/128 Duty
Gray Scale	4 bits
IC	SSD1327
Arayüz	6800,8080,SPI,I2C
Boyut	1.5 inç

Maksimum Değerler

Parameter	Sembol	Minumum Deger	Maksimum Deger	Birim
Low voltage power supply, power supply for I/O pins	VCI	-0.3	4.0	V
Supply Voltage for Logic	VDD	-0.5	2.75	V
Supply Voltage for Display	VCC	-0.5	19.0	V
Çalışma Sıcaklığı	TOP	-40	+80	°C
Saklama Sıcaklığı	TSTG	-40	+85	°C

Elektronik Özellikleri

Kalem	Sembol	Durum	Minumum Deger	Tipik Deger	Maksimum Deger	Birim
Low voltage power supply, power supply for I/O pins	VCI		2.8	3	3.3	V
Supply Voltage for Display	VCC	－	14	14.5	15	V
Supply Voltage for Logic	VDD	－	2.4	－	2.6	V
High Level Input	VIH	－	0.8×VCI	－	VCI	V
Low Level Input	VIL	－	0	－	0.2×VCI	V
High Level Output	VOH	－	0.9×VCI	－	VCI	V
Low Level Output	VOL	－	0	－	0.1×VCI	V
50% Check Board operating Current		VCC =14.5V	－	24	36	mA

Arayüz Pin Fonksiyonlari

No.

Sembol

Fonksiyon

VSS

Ground pin. It must be connected to external ground.

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.

VCI

Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.

VDD

Power supply pin for core logic operation.
VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated
Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances.

BS1

MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select.
Bus Interface selection

BS[2:1]	Interface
00	4 line SPI
01	I2C
11	8-bit 8080 parallel
10	8-bit 6800 parallel

Note (1) 0 is connected to VSS (2) 1 is connected to VCI

BS2

VSS

Ground pin. It must be connected to external ground.

IREF

This pin is the segment output current reference pin

CS#

This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

RES#

This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.

D/C

This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.

W/R#

This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.