Home Prodotti Display OLED Display OLED Grafici WEO128128A

1.5" COG Display OLED Monocromatico 128x128

Modello numero WEO128128A

►Tipo: grafico
►Struttura: COG
►Dimensione: 1.5 pollici
►128x128 a matrice di punti
►IC:SSD1327
►Alimentatore 3V
►1/128 duty
►Interfaccia: 6800, 8080, SPI, I2C
►Colore display: Bianco / Giallo
►Support Grayscale
►Altre opzioni FPC disponibili nella tabella di seguito

Descrizione


   Opzioni FPC

 

DISEGNO

OLED Display 128x128, 128x128 OLED Display, 128x128 pixel OLED Module - WEO128128A

 

Data source ref: WEO128128ALAP3N00000

SPECIFICHE TECNICHE

Specifiche generali

Articolo Dimensioni Unità
A matrice di punti 128 x 128 Dots
Dimensione del modulo 33.80 x 36.50 x 2.05 mm
Area attiva 26.86 x 26.86 mm
Dimensioni del Dot 0.185 x 0.185 mm
Passo del Dot 0.210 x 0.210 mm
Modalità display Matrice passiva
Colore display monocromatici
Drive Duty 1/128 Duty
Gray Scale 4 bits
IC SSD1327
Interfaccia 6800,8080,SPI,I2C
Dimensione (Diagonale) 1.5 pollici

Valori massimi assoluti

Parameter Simbolo Valore Min Valore massimo Unità
Low voltage power supply, power supply for I/O pins VCI -0.3 4.0 V
Supply Voltage for Logic VDD -0.5 2.75 V
Supply Voltage for Display VCC -0.5 19.0 V
Temperatura di lavoro TOP -40 +80 °C
Temperatura di stock TSTG -40 +85 °C

Caratteristiche elettriche

Articolo Simbolo Condizione Valore Min Valore tipico Valore massimo Unità
Low voltage power supply, power supply for I/O pins VCI   2.8 3 3.3 V
Supply Voltage for Display VCC 14 14.5 15 V
Supply Voltage for Logic VDD 2.4 2.6 V
High Level Input VIH 0.8×VCI VCI V
Low Level Input VIL 0 0.2×VCI V
High Level Output VOH 0.9×VCI VCI V
Low Level Output VOL 0 0.1×VCI V
50% Check Board operating Current VCC =14.5V 24 36 mA

Funzione dei Pin di Interfaccia

No. Simbolo Funzione
1 VSS Ground pin. It must be connected to external ground.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.
4 VCI Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.
5 VDD Power supply pin for core logic operation.
VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated
Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances.
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select.
Bus Interface selection
BS[2:1] Interface
00 4 line SPI
01 I2C
11 8-bit 8080 parallel
10 8-bit 6800 parallel
Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
7 BS2
8 VSS Ground pin. It must be connected to external ground.
9 IREF This pin is the segment output current reference pin
10 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
11 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
12 D/C This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
13 W/R# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.

Opzioni FPC:

Immagine FPC Length PIN Pitch ZIF FPC or HOTBAR FPC Interfaccia FPC No. Create Date
FPC2050002411XXXXX03_WEO128128ALAP3N00000 25.05 24 0.5 ZIF 6800,8080,SPI,I2C FPC2050002411XXXXX03 20150901
FPC2050002411XXXXX12_WEO128128AWAP3N00002 41 24 0.5 ZIF 6800,8080,4-Wire SPI,I2C FPC2050002411XXXXX12 20200116

Prodotti correlati

go top
close

Valorizziamo la tua privacy

Facendo clic su "Consenti tutti i cookie", accetti la memorizzazione dei cookie sul tuo dispositivo per migliorare la navigazione del sito, analizzare l'utilizzo del sito e assistere nei nostri sforzi di marketing e prestazioni. Puoi trovare ulteriori informazioni su questo argomento nella nostra politica. Informativa sulla privacy

Valorizziamo la tua privacy

Winstar e alcune terze parti utilizzano i cookie su www.winstar.com.tw. I dettagli relativi ai tipi di cookie, al loro scopo e alle terze parti coinvolte sono descritti di seguito e nella nostra Informativa sui cookie. Fare clic su "Consenti tutti" per acconsentire all'uso dei cookie e ottenere la migliore esperienza possibile sui nostri siti web. Puoi anche impostare le tue preferenze o rifiutare i cookie (ad eccezione dei cookie strettamente necessari).

Gestisci le preferenze di consenso

Sempre attivo
Cookie essenziali

Questi cookie sono essenziali per permetterti di navigare nel sito web e utilizzare le sue funzionalità, come impostare le tue preferenze sulla privacy, effettuare il login o compilare moduli.

Cookie di analisi

Questi sono noti anche come "cookie statistici"; raccolgono informazioni su come utilizzi un sito web, come quali pagine hai visitato e quali link hai cliccato. Vedi dettagli.