Startseite Produkte OLED-Anzeige Grafik-OLED-Anzeigen WEO012864V

0.96" 128x64 SSD1315 OLED-Anzeige

Modellnummer WEO012864V

►Typ: Grafik
►Bauweise: COG
►Größe: 0,96 Zoll
►128 x 64 Punktmatrix
►IC:SSD1315
►3-V-Stromversorgung
►1/64 duty
►Schnittstelle: SPI, I2C
►die Farbe des Displays: Weiß / Gelb

Zeichnung

SSD1315 OLED, 0.96 inch 128x64 SSD1315 OLED Display Module - WEO012864V

Data source ref: WEO012864VWPP3N0Y000

Technische Daten

mechanische Daten

Artikel Ausmaß Einheit
Punktmatrix 128 x 64 Dots
Abmaße der modul 24,74 x 16,90 x 1.26 mm
Aktiver Bereich 21,74 x 10,86 mm
Pixelgröße 0,15 x 0,15 mm
Pixelabstand 0,17 x 0,17 mm
der Anzeigemodus Passive Matrix
die Farbe des Displays Monochrome
Drive Duty 1/64 Duty
IC SSD1315
Schnittstelle 4-line/3-line SPI, I2C
Größe 0,96 Zoll

Absolute Grenzwerte

Parameter Symbol Mindestwert Maximalwert Einheit
Supply Voltage for Logic VDD -0,3 4,0 V
Charge Pump Regulator VBAT -0,3 6,0 V
Supply Voltage for Display VCC 0 18,0 V
Betriebstemperatur TOP -30 +70 °C
Lagertemperatur TSTG -30 +70 °C

elektronische Eingenschaften

DC elektronische Eingenschaften

Artikel Symbol Bedingung Mindestwert typischer Wert Maximalwert Einheit
Supply Voltage for Logic VDD 2,8 3,0 3,3 V
Supply Voltage for Display VCC 7,0 7,5 8,0 V
Input High Volt. VIH 0,8×VDD VDD V
Input Low Volt. VIL 0 0,2×VDD V
Output High Volt. VOH 0,9×VDD VDD V
Output Low Volt. VOL 0 0,1×VDD V
Operating Current for VCC (50% display ON) ICC 6 12 mA

Schnittstelle Pin-Funktion

No. Symbol Beschreibung
1 C2N C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
2 C2P
3 C1P C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used.
6 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
7 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
9 BS0 Communicating Protocol Select
These pins are MCU interface selection input. See the
following table:
BS[1:0] Interface
00 4-line SPI
01 3-line SPI
10 I2C
10 BS1
11 CS# Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
12 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
13 D/C# In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
14~16 D0~D2 When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
17 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA.
18 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
19 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
20 VLSS Ground of Analog Circuit
This is an analog ground pin. It should be connected to VSS externally.
go top
close

Wir schätzen Ihre Privatsphäre

Durch Klicken auf „Alle Cookies zulassen“ stimmen Sie der Speicherung von Cookies auf Ihrem Gerät zu, um die Navigation auf der Website zu verbessern, die Nutzung der Website zu analysieren und unsere Marketing- und Leistungsbemühungen zu unterstützen. Weitere Informationen zu diesem Thema finden Sie in unserer Richtlinie. Datenschutzrichtlinie

Wir schätzen Ihre Privatsphäre

Winstar und bestimmte Drittparteien verwenden Cookies auf www.winstar.com.tw. Die Einzelheiten zu den Arten von Cookies, ihrem Zweck und den beteiligten Drittparteien sind unten sowie in unserer Cookie-Richtlinie beschrieben. Klicken Sie auf „Alle zulassen“, um unserer Verwendung von Cookies zuzustimmen und die bestmögliche Erfahrung auf unseren Websites zu erzielen. Sie können auch Ihre Präferenzen festlegen oder Cookies ablehnen (mit Ausnahme der unbedingt erforderlichen Cookies).

Einwilligungspräferenzen verwalten

Immer aktiv
Notwendige Cookies

Diese Cookies sind unerlässlich, um Ihnen das Navigieren auf der Website zu ermöglichen und ihre Funktionen zu nutzen, wie z. B. das Festlegen Ihrer Datenschutzpräferenzen, das Einloggen oder das Ausfüllen von Formularen.

Analyse-Cookies

Diese Cookies, auch als „Statistik-Cookies“ bekannt, sammeln Informationen darüber, wie Sie eine Website nutzen, z. B. welche Seiten Sie besucht und auf welche Links Sie geklickt haben. Siehe Details.