Home Prodotti Display OLED Display OLED Grafici WEO012864V

0.96" 128x64 SSD1315 Moduli OLED

Modello numero WEO012864V

►Tipo: grafico
►Struttura: COG
►Dimensione: 0.96 pollici
►128 x 64 a matrice di punti
►IC:SSD1315
►Alimentatore 3V
►1/64 duty
►Interfaccia: SPI, I2C
►Colore display: Bianco / Giallo

DISEGNO

SSD1315 OLED, 0.96 inch 128x64 SSD1315 OLED Display Module - WEO012864V

Data source ref: WEO012864VWPP3N0Y000

SPECIFICHE TECNICHE

Dati meccanici

Articolo Dimensioni Unità
A matrice di punti 128 x 64 Dots
Dimensione del modulo 24.74 x 16.90 x 1.26 mm
Area attiva 21.74 x 10.86 mm
Dimensioni del Dot 0.15 x 0.15 mm
Passo del Dot 0.17 x 0.17 mm
Modalità display Matrice passiva
Colore display Monochrome
Drive Duty 1/64 Duty
IC SSD1315
Interfaccia 4-line/3-line SPI, I2C
Dimensione 0.96 pollici

Valori massimi assoluti

Parameter Simbolo Valore Min Valore massimo Unità
Supply Voltage for Logic VDD -0.3 4.0 V
Charge Pump Regulator VBAT -0.3 6.0 V
Supply Voltage for Display VCC 0 18.0 V
Temperatura di lavoro TOP -30 +70 °C
Temperatura di stock TSTG -30 +70 °C

Caratteristiche elettriche

DC Caratteristiche elettriche

Articolo Simbolo Condizione Valore Min Valore tipico Valore massimo Unità
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 7.0 7.5 8.0 V
Input High Volt. VIH 0.8×VDD VDD V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH 0.9×VDD VDD V
Output Low Volt. VOL 0 0.1×VDD V
Operating Current for VCC (50% display ON) ICC 6 12 mA

Funzione dei Pin di Interfaccia

No. Simbolo Funzione
1 C2N C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
2 C2P
3 C1P C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used.
6 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
7 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
9 BS0 Communicating Protocol Select
These pins are MCU interface selection input. See the
following table:
BS[1:0] Interface
00 4-line SPI
01 3-line SPI
10 I2C
10 BS1
11 CS# Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
12 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
13 D/C# In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
14~16 D0~D2 When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
17 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA.
18 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
19 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
20 VLSS Ground of Analog Circuit
This is an analog ground pin. It should be connected to VSS externally.
go top
close

Valorizziamo la tua privacy

Facendo clic su "Consenti tutti i cookie", accetti la memorizzazione dei cookie sul tuo dispositivo per migliorare la navigazione del sito, analizzare l'utilizzo del sito e assistere nei nostri sforzi di marketing e prestazioni. Puoi trovare ulteriori informazioni su questo argomento nella nostra politica. Informativa sulla privacy

Valorizziamo la tua privacy

Winstar e alcune terze parti utilizzano i cookie su www.winstar.com.tw. I dettagli relativi ai tipi di cookie, al loro scopo e alle terze parti coinvolte sono descritti di seguito e nella nostra Informativa sui cookie. Fare clic su "Consenti tutti" per acconsentire all'uso dei cookie e ottenere la migliore esperienza possibile sui nostri siti web. Puoi anche impostare le tue preferenze o rifiutare i cookie (ad eccezione dei cookie strettamente necessari).

Gestisci le preferenze di consenso

Sempre attivo
Cookie essenziali

Questi cookie sono essenziali per permetterti di navigare nel sito web e utilizzare le sue funzionalità, come impostare le tue preferenze sulla privacy, effettuare il login o compilare moduli.

Cookie di analisi

Questi sono noti anche come "cookie statistici"; raccolgono informazioni su come utilizzi un sito web, come quali pagine hai visitato e quali link hai cliccato. Vedi dettagli.