私たちはあなたのプライバシーを大切にします
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー
WEO012864Vは0.96インチCOG構造の グラフィック有機ELディスプレイで、解像度は128x64です。このモジュールは 価額の競争力があるコンシューマー級です。 SSD1315 ICを内蔵し、 I2Cと3線式 /4線式 のSPI インターフェースをサポート致します。ロジックの電源電圧は3Vで、Display電源電圧は7.5Vです。50%チェックボード電流での表示は 6mA @ 7.5Vcc (標準値)で、駆動デューティは1/64です。内部チャージポンプ電源と外部 VCC 電源をサポートしております。
この0.96 インチCOG 構造の グラフィック有機ELディスプレイはウェアラブルデバイス、スマートホームアプリケーション などに適しております。 操作温度範囲は -30℃~+70℃で、 保存温度範囲は -30℃~+70です。
項目 | 標準値 | 単位 |
---|---|---|
ドットマトリックス(解像度) | 128 x 64 Dots | - |
外形寸法 | 24.74 x 16.90 x 1.26 | mm |
有効表示エリア | 21.74 x 10.86 | mm |
ドットサイズ | 0.15 x 0.15 | mm |
ドットピッチ | 0.17 x 0.17 | mm |
表示モード | パッシブマトリクス | |
発光色 | モノクロ | |
駆動方法 | 1/64 Duty | |
コントローラー IC | SSD1315 | |
インターフェイス | 4-line/3-line SPI, I2C | |
サイズ | 0.96 インチ |
パラメーター | 記号 | 最小値 | 最大値 | 単位 |
---|---|---|---|---|
ロジック電源電圧 | VDD | -0.3 | 4.0 | V |
Charge Pump Regulator | VBAT | -0.3 | 6.0 | V |
Display電源電圧 | VCC | 0 | 18.0 | V |
操作温度 | TOP | -30 | +70 | °C |
保存温度 | TSTG | -30 | +70 | °C |
項目 | 記号 | 条件 | 最小値 | 典型値 | 最大値 | 単位 |
---|---|---|---|---|---|---|
ロジック電源電圧 | VDD | - | 2.8 | 3.0 | 3.3 | V |
Display電源電圧 | VCC | - | 7.0 | 7.5 | 8.0 | V |
高レベル入力 | VIH | - | 0.8×VDD | - | VDD | V |
低レベル入力 | VIL | - | 0 | - | 0.2×VDD | V |
高レベル出力 | VOH | - | 0.9×VDD | - | VDD | V |
低レベル出力 | VOL | - | 0 | - | 0.1×VDD | V |
Operating Current for VCC (50% display ON) | ICC | - | - | 6 | 12 | mA |
No. | 記号 | 説明 | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
1 | C2N | C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor. | ||||||||
2 | C2P | |||||||||
3 | C1P | C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor. | ||||||||
4 | C1N | |||||||||
5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used. |
||||||||
6 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. When charge pump is enabled, a capacitor should be connected between this pin and VSS. |
||||||||
7 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
||||||||
8 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
||||||||
9 | BS0 | Communicating Protocol Select These pins are MCU interface selection input. See the following table:
|
||||||||
10 | BS1 | |||||||||
11 | CS# | Chip Select This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low. |
||||||||
12 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
||||||||
13 | D/C# | In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
||||||||
14~16 | D0~D2 | When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||||
17 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA. |
||||||||
18 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
||||||||
19 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. When charge pump is enabled, a capacitor should be connected between this pin and VSS. |
||||||||
20 | VLSS | Ground of Analog Circuit This is an analog ground pin. It should be connected to VSS externally. |
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー