我們重視您的隱私
通過點擊「允許所有 Cookie」,代表您同意在您的設備上存儲 Cookie 以增強網站瀏覽體驗、分析網站使用情況並協助我們的行銷和網站效能優化工作。您可以在我們的隱私權政策中找到有關於此的更多資訊。
WEA128128A模組是WEO128128A衍生產品,WEA128128A在模組上有搭配PCB板,顯示畫面由128x128像素組成,對角線尺寸為1.5吋。 這種有4個鎖孔設計的PCB板,可讓客戶固定應用產品與模組時更加方便。 WEA128128A OLED模組內建SSD1327 IC並支援4線SPI介面;可選I2C介面。模組支援灰階16 (4bits) 驅動方式為1/128,邏輯電源電壓為3.3V~5V,50%顯示畫面耗電流為160 mA 工作電壓為3.3V(Typical值)。
此OLED模組非常適合運用在智能家電、醫療設備、智能檢測、儀表板等等。WEA128128A模組工作溫度為-40℃至+80℃;儲存溫度為-40℃至+85℃。
項目 | 尺寸 | 單位 |
---|---|---|
點陣 | 128 x 128 Dots | - |
模組尺寸 | 34.2 x 45.5 x 3.16 | mm |
有效區域 | 26.86 x 26.86 | mm |
像素大小 | 0.185 x 0.185 | mm |
像素間距 | 0.210 x 0.210 | mm |
顯示模式 | 被動矩陣 | |
發光顏色 | 單色 | |
驅動方式 | 1/128 Duty | |
灰階 | 4 bits | |
IC | SSD1327 | |
介面 | 4線 SPI / 可選I2C | |
尺寸 | 1.5 吋 |
參數 | 符號 | 最小值 | 最大值 | 單位 |
---|---|---|---|---|
邏輯電源電壓 | VCC | 1.65 | 5.5 | V |
工作溫度 | TOP | -40 | +80 | °C |
儲存溫度 | TSTG | -40 | +85 | °C |
項目 | 符號 | 條件 | 最小值 | 典型值 | 最大值 | 單位 |
---|---|---|---|---|---|---|
邏輯電源電壓(3V/5V) | VCC | - | 2.8 | 3.3 | 5.2 | V |
輸入高準位 | VIH | - | 0.8×VCC | - | VCC | V |
輸入低準位 | VIL | - | 0 | - | 0.2×VCC | V |
輸出高準位 | VOH | - | 0.9×VCC | - | VCC | V |
輸出低準位 | VOL | - | 0 | - | 0.1×VCC | V |
50%顯示畫面耗電流 | ICC | VCC=3.3V | - | 160 | 320 | mA |
No. | 符號 | 功能說明 |
---|---|---|
1 | GND | This is a ground pin. |
2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. |
3 | D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. |
4 | D1 | |
5 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
6 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. |
7 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
通過點擊「允許所有 Cookie」,代表您同意在您的設備上存儲 Cookie 以增強網站瀏覽體驗、分析網站使用情況並協助我們的行銷和網站效能優化工作。您可以在我們的隱私權政策中找到有關於此的更多資訊。