我们重视您的隐私
通过点击「允许所有 Cookie」，代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。
产品叙述
WEO12864A 1.54寸OLED是一款COG 绘图型单色被动式PMOLED显示器模块，面板解析度128x64 pixels。 WEO12864A内置SSD1309 controller控制器, 支援多种传输介面: 6800 8-bite, 8080 8-bit 平行介面, I2C 与4线SPI串列介面，使用3V驱动。 WEO12864A的模块尺寸为42.04 x 27.22 mm， AA区尺寸为35.05 x 17.51 mm。
WEO12864A为COG结构的OLED显示器模块，有机自发光，无须背光源，模块轻薄且低耗电流，WEO012864A模块非常适合手持式产品、量测仪器、家用产品、POS系统、物联网、通讯设备与医疗仪器等等。此模块的工作温度是-40℃至+80℃，储存温度-40℃至+85℃。
可选 FPC
规格图
Data source ref:WEO012864ALAP3N00000
产品规格
规格说明
| 项目 | 规格说明 | 单位 |
|---|---|---|
| 点阵(分辨率) | 128 x 64 | － |
| 模块尺寸 | 42.04 × 27.22 × 1.41 | mm |
| 有效区域 | 35.05 × 17.51 | mm |
| 像素大小 | 0.249 × 0.249 | mm |
| 像素间距 | 0.274 × 0.274 | mm |
| 显示模式 | Passive Matrix 被动矩阵 | |
| 显示颜色 | 单色 | |
| 驱动方式 | 1/64 Duty | |
| IC | SSD1309 | |
| 接口 | 6800/8080/4线 SPI/I2C | |
| 尺寸 | 1.54 寸 | |
最大绝对额定值
| 参数 | 符号 | 最小值 | 最大值 | 单位 |
|---|---|---|---|---|
| 逻辑电源电压 | VDD | -0.3 | 4 | V |
| 显示电源电压 | VCC | 0 | 17 | V |
| 工作温度 | TOP | -40 | +80 | °C |
| 储存温度 | TSTG | -40 | +85 | °C |
电气特性
| 项目 | 符号 | 条件 | 最小值 | 典型值 | 最大值 | 单位 |
|---|---|---|---|---|---|---|
| 逻辑电源电压 | VDD | － | 1.65 | 3.0 | 3.3 | V |
| 显示电源电压 | VCC | － | 7.0 | 12.5 | 13.0 | V |
| 输入高准位 | VIH | － | 0.8×VDD | － | － | V |
| 输入低准位 | VIL | － | － | － | 0.2×VDD | V |
| 输出高准位 | VOH | － | 0.9×VDD | － | － | V |
| 书出低准位 | VOL | － | － | － | 0.1×VDD | V |
| 5显示 50% 像素 | VCC =12.5V | － | 16 | 45 | mA | |
Pin功能定义
| No. | 符号 | 功能说明 | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | NC(GND) | No connection | |||||||||||||||
| 2 | VLSS | This is an analog ground pin | |||||||||||||||
| 3 | VSS | Ground. | |||||||||||||||
| 4 | NC | No connection | |||||||||||||||
| 5 | VDD | Power supply pin for core logic operation | |||||||||||||||
| 6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
Note (1) 0 is connected to VSS (2) 1 is connected to VDD |
|||||||||||||||
| 7 | BS2 | ||||||||||||||||
| 8 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
|||||||||||||||
| 9 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
|||||||||||||||
| 10 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
| 11 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 12 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 13-20 | D0~D7 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
| 21 | IREF | This pin is the segment output current reference pin. IREF is supplied externally. |
|||||||||||||||
| 22 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
|||||||||||||||
| 23 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
| 24 | NC(GND) | No connection |
FPC Options:
| Drawing | FPC Length | PIN | Pitch | ZIF FPC or HOTBAR FPC | Interface | FPC No. | Create Date |
|---|---|---|---|---|---|---|---|
 |
37.19 | 24 | 0.5 | ZIF | 6800/8080/4-SPI/I2C | FPC2050002411XXXXX05 | 20160627 |
 |
51.05 | 30 | 0.5 | ZIF | 6800/8080/4-SPI/I2C | FPC2050003011XXXXX32 | 20190926 |