我們重視您的隱私
通過點擊「允許所有 Cookie」，代表您同意在您的設備上存儲 Cookie 以增強網站瀏覽體驗、分析網站使用情況並協助我們的行銷和網站效能優化工作。您可以在我們的隱私權政策中找到有關於此的更多資訊。
產品敘述
WEO12864A 1.54吋OLED是一款COG 繪圖型單色被動式PMOLED顯示器模組，面板解析度128x64 pixels。WEO12864A 128x64 OLED模組內建SSD1309 controller控制器, 支援多種傳輸介面: 6800 8-bite, 8080 8-bit 平行介面, I2C 與4線SPI串列介面，使用3V驅動。 WEO12864A的模組尺寸為42.04 x 27.22 mm， AA區尺寸為35.05 x 17.51 mm。
WEO12864A為COG結構的OLED顯示器模組，有機自發光，無須背光源，模組輕薄且低耗電流，WEO012864A模組非常適合穿載裝置、手持式產品、量測儀器、家用產品、POS系統、物聯網、通訊設備與醫療儀器等等。此模組的工作溫度是-40℃至+80℃，儲存溫度-40℃至+85℃。
可選 FPC
規格圖
Data source ref:WEO012864ALAP3N00000
產品規格
規格說明
| 項目 | 規格說明 | 單位 |
|---|---|---|
| 點陣(解析度) | 128 x 64 | － |
| 模組尺寸 | 42.04 × 27.22 × 1.41 | mm |
| 有效區域 | 35.05 × 17.51 | mm |
| 像素大小 | 0.249 × 0.249 | mm |
| 像素間距 | 0.274 × 0.274 | mm |
| 顯示模式 | Passive Matrix 被動矩陣 | |
| 顯示顏色 | 單色 | |
| 驅動方式 | 1/64 Duty | |
| IC | SSD1309 | |
| 介面 | 6800/8080/4線 SPI/I2C | |
| 尺寸 | 1.54 吋 | |
最大絕對額定值
| 參數 | 符號 | 最小值 | 最大值 | 單位 |
|---|---|---|---|---|
| 邏輯電源電壓 | VDD | -0.3 | 4 | V |
| 顯示電源電壓 | VCC | 0 | 17 | V |
| 工作溫度 | TOP | -40 | +80 | °C |
| 儲存溫度 | TSTG | -40 | +85 | °C |
電氣特性
| 項目 | 符號 | 條件 | 最小值 | 典型值 | 最大值 | 單位 |
|---|---|---|---|---|---|---|
| 邏輯電源電壓 | VDD | － | 1.65 | 3.0 | 3.3 | V |
| 顯示電源電壓 | VCC | － | 7.0 | 12.5 | 13.0 | V |
| 輸入高準位 | VIH | － | 0.8×VDD | － | － | V |
| 輸入低準位 | VIL | － | － | － | 0.2×VDD | V |
| 輸出高準位 | VOH | － | 0.9×VDD | － | － | V |
| 書出低準位 | VOL | － | － | － | 0.1×VDD | V |
| 顯示 50% 像素 | VCC =12.5V | － | 16 | 45 | mA | |
Pin功能定義
| No. | 符號 | 功能說明 | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | NC(GND) | No connection | |||||||||||||||
| 2 | VLSS | This is an analog ground pin | |||||||||||||||
| 3 | VSS | Ground. | |||||||||||||||
| 4 | NC | No connection | |||||||||||||||
| 5 | VDD | Power supply pin for core logic operation | |||||||||||||||
| 6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
Note (1) 0 is connected to VSS (2) 1 is connected to VDD |
|||||||||||||||
| 7 | BS2 | ||||||||||||||||
| 8 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
|||||||||||||||
| 9 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
|||||||||||||||
| 10 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
| 11 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 12 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 13-20 | D0~D7 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
| 21 | IREF | This pin is the segment output current reference pin. IREF is supplied externally. |
|||||||||||||||
| 22 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
|||||||||||||||
| 23 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
| 24 | NC(GND) | No connection |
FPC Options:
| Drawing | FPC Length | PIN | Pitch | ZIF FPC or HOTBAR FPC | Interface | FPC No. | Create Date |
|---|---|---|---|---|---|---|---|
 |
37.19 | 24 | 0.5 | ZIF | 6800/8080/4-SPI/I2C | FPC2050002411XXXXX05 | 20160627 |
 |
51.05 | 30 | 0.5 | ZIF | 6800/8080/4-SPI/I2C | FPC2050003011XXXXX32 | 20190926 |