Model No. WF52QTZBSDBN0
►Size : 5.2”
►Resolution : 480 x 128 dots
►View Direction : 6H
►Interface : 8080, MPU
►Controller IC : SSD1963
►Control-Board : Yes
►Brightness (cd/m²): 400
►Frame Through Hole : Yes
►Touch Screen : Without touch screen
►O-Film : Yes
WF52QTZBSDBN0 is a 5.2-inch bar-type TFT LCD display with O-Film technology, offering wide viewing angles. The module is equipped with an integrated SSD1963 controller IC and control board, supporting 8080 MPU interface options in both 8-bit and 16-bit configurations. Pins 33 to 36 are pre-assigned for backlight power, eliminating the need for additional backlight circuitry. The display also includes four screw holes on its PCB for easy mounting in various applications.
It has a resolution of 480×128 pixels and a brightness of 400 cd/m². The supply voltage for the LCM (VCC) ranges from 3.0V to 3.3V (typical value: 3.1V). This bar-type TFT display module can operate within a temperature range of -20℃ to +70℃ and can be stored in temperatures ranging from -30℃ to +80℃.
If you need higher brightness, you can opt for the WF52QSZBSDBN0 model.
| Item | Dimension | Unit |
|---|---|---|
| Size | 5.2 | inch |
| Dot Matrix | 480 × RGB × 128 | dots |
| Module dimension | 180.0 × 65.0 × 8.8 | mm |
| Active area | 127.152 × 33.9072 | mm |
| Dot pitch | 0.0883 × 0.2649 | mm |
| LCD type | TFT, Normally White, Transmissive | |
| View Direction | 6 o'clock | |
| Gray Scale Inversion Direction | 12 o'clock | |
| Aspect Ratio | Bar Type | |
| Backlight Type | LED, Normally White | |
| Controller IC | SSD1963 | |
| Interface | Digital 8080 family MPU 8bit/16bit | |
| Touch Panel | Without touch panel (screen) | |
| Surface | Anti-Glare | |
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Operating Temperature | TOP | -20 | － | +70 | ℃ |
| Storage Temperature | TST | -30 | － | +80 | ℃ |
| Item | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Supply Voltage For LCM | VDD | － | 3.0 | 3.1 | 3.3 | V |
| Supply Current For LCM | IDD | － | － | 200 | － | mA |
| Pin | Symbol | Function |
|---|---|---|
| 1 | GND | System round pin of the IC. Connect to system ground. |
| 2 | VDD | Power Supply : +3.3V |
| 3 | BL_E | Backlight control signal , H: On \ L: Off |
| 4 | D/C | Data/Command select |
| 5 | WR | Write strobe signal |
| 6 | RD | Read strobe signal |
| 7 | DB0 | Data bus |
| 8 | DB1 | Data bus |
| 9 | DB2 | Data bus |
| 10 | DB3 | Data bus |
| 11 | DB4 | Data bus |
| 12 | DB5 | Data bus |
| 13 | DB6 | Data bus |
| 14 | DB7 | Data bus |
| 15 | DB8 | Data bus (When select 8bits mode, this pin is NC) |
| 16 | DB9 | Data bus (When select 8bits mode, this pin is NC) |
| 17 | DB10 | Data bus (When select 8bits mode, this pin is NC) |
| 18 | DB11 | Data bus (When select 8bits mode, this pin is NC) |
| 19 | DB12 | Data bus (When select 8bits mode, this pin is NC) |
| 20 | DB13 | Data bus (When select 8bits mode, this pin is NC) |
| 21 | DB14 | Data bus (When select 8bits mode, this pin is NC) |
| 22 | DB15 | Data bus (When select 8bits mode, this pin is NC) |
| 23 | NC | No connect |
| 24 | NC | No connect |
| 25 | CS | Chip select |
| 26 | RESET | Hardware reset |
| 27 | LR | Right /Left selection; Default R/L is Pull High |
| 28 | UD | Up/down selection; Default U/D is Pull High |
| 29 | NC | No connection |
| 30 | NC | No connection |
| 31 | NC | No connection |
| 32 | NC | No connection |
| 33 | VLED- | VLED- for B/L LED inverter (GND) |
| 34 | VLED- | VLED- for B/L LED inverter (GND) |
| 35 | VLED+ | VLED+ for B/L LED inverter (+5V) |
| 36 | VLED+ | VLED+ for B/L LED inverter (+5V) |
| Pin | Symbol | Function |
|---|---|---|
| 1 | NC(FG) | No connect (Frame Grand) |
| 2 | GND | System round pin of the IC. Connect to system ground. |
| 3 | VDD | Power Supply : +3.3V |
| 4 | BLE | Backlight control signal , H: On \ L: Off |
| 5 | WR | Write strobe signal |
| 6 | RD | Read strobe signal |
| 7 | CS | Chip select |
| 8 | D/C | Data/Command select |
| 9 | NC | No connect |
| 10 | RESET | Hardware reset |
| 11 | DB0 | Data bus |
| 12 | DB1 | Data bus |
| 13 | DB2 | Data bus |
| 14 | DB3 | Data bus |
| 15 | DB4 | Data bus |
| 16 | DB5 | Data bus |
| 17 | DB6 | Data bus |
| 18 | DB7 | Data bus |
| 19 | NC | No connect |
| 20 | NC | No connect |
| 21 | VLED+ | VLED+ for B/L LED inverter (+5V) |
| 22 | VLED- | VLED- for B/L LED inverter (GND) |
| 23 | NC | No connect |
| 24 | NC | No connect |
| 25 | NC | No connect |
| 26 | GND | System round pin of the IC. Connect to system ground. |
By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.