Model No. WAA0290A2ABA8NXXX000
►Size: 2.9"
►Resolution: 296x128 dots
►Interface: MCU / SPI
►Touch Screen : With capacitive touch panel
►The display refreshes black-and-white e-paper displays.
►Front Light : No
WAA0290A2ABA8NXXX000 is a 2.9" Electronic Paper Display (EPD) with capacitive touch panel. The display is capable of showing black-and-white images with full 1-bit display capability. The 2.9-inch active area contains 296x128 pixels. The module uses a TFT array to drive the electrophoresis display, with integrated circuits including gate driver, source driver, MCU interface, timing controller, oscillator, DC-DC converter, SRAM, LUT, and VCOM control. The module can be used in portable electronic devices, such as in Electronic Shelf Label (ESL) systems.
| Parameter | Specifications | Unit |
|---|---|---|
| Screen Size | 2.9 | Inch |
| Display Resolution | 296(H)×128(V) | Pixel |
| Active Area | 29.056×66.896 | mm |
| Pixel Pitch | 0.227×0.226 | mm |
| Pixel Configuration | Rectangle | |
| Outline Dimension | 36.7(H) × 79.0 (V) × 1.575(D) | mm |
| Module Weight | 8.31±0.5 | g |
| Parameter | Symbol | Rating | Unit |
|---|---|---|---|
| Logic supply voltage | VCI | -0.5 to +4.0 | V |
| Logic Input voltage | VIN | -0.5 to VCI +0.5 | V |
| Logic Output voltage | VOUT | -0.5 to VCI +0.5 | V |
| Operating Temp range | TOPR | 0 to +50 | ºC |
| Storage Temp range | TSTG | -25 to+70 | ºC |
| Optimal Storage Temp | TSTGo | 23±2 | ºC |
| Optimal Storage Humidity | HSTGo | 55±10 | %RH |
| No. | Name | I/O | Description |
|---|---|---|---|
| 1 | NC | Do not connect with other NC pins | |
| 2 | GDR | O | N-Channel MOSFET Gate Drive Control |
| 3 | RESE | P | Current sense input for control loop. |
| 4 | NC | NC | Do not connect with other NC pins |
| 5 | VSH2 | C | Positive source driving voltage (Red) |
| 6 | TSCL | O | I2C interface to digital temperature sensor Clock pin |
| 7 | TSDA | I/O | I2C interface to digital temperature sensor Data pin |
| 8 | BS1 | I | Bus Inteface selection pin |
| 9 | BUSY | O | Busy state output pin |
| 10 | RES# | I | Reset signal input. Active Low |
| 11 | D/C# | I | Data / Command control pin |
| 12 | CS# | I | Chip select input pin |
| 13 | SCL | I | Serial Clock pin (SPI) |
| 14 | SDA | I/O | Serial Data pin (SPI) |
| 15 | VDDIO | P | Power Suupply for interface logic pins. It should be connected with VCI |
| 16 | VCI | P | Power Supply for the chip |
| 17 | VSS | P | Ground |
| 18 | VDD | C | Core logic power pin VDD can be regulated internally from VCI. A capacitor should be connected between VDD and VSS |
| 19 | VPP | P | FOR TEST |
| 20 | VSH1 | C | Positive Source driving voltage |
| 21 | VGH | P | Power Supply pin for Positive Gate driving voltage and VSH1 |
| 22 | VSL | P | Negative Source driving voltage |
| 23 | VGL | P | Power Supply pin for Negative Gate driving voltage VCOM and VSL |
| 24 | VCOM | O | VCOM driving voltage |
Note: I: Input, O: Output, P: Power, D: Dummy, S: Shorted line, M: Mark, PI: Power input, PO: Power output, I/O: Input / Output, PS: Power Setting, C: Capacitor pin.
By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.
