نزل المنتجات وحدات OLED شاشات جرافيك OLED WEF012864H

رقم الموديل WEF012864H

◄النوع: جرافيك(بإطار)
◄االهيكل: COG+FR
◄الحجم: 2.42 بوصة
◄مصفوفة نقطية 128*64
◄وحدة تحكم مدمجة SSD1309
◄مزود طاقة +3 فولت
◄1/64 حمولة
◄الواجهة: 6800/8080/SPI/I2C
◄لون العرض: أبيض / أصفر / أزرق سماوي / أخضر

الرسم

WEF012864H
Data source ref:WEF012864HWPP3N00F00

المواصفات

وظيفة دبوس واجهة التوصيل

.Pin No الرمز الوظيفة
1 (NC(Vss (No connection. (ground
2 VCC .Power supply for panel driving voltage. This is also the most positive power voltage supply pin
3 VCOMH .COM signal deselected voltage level
.A capacitor should be connected between this pin and VSS
4 IREF .This pin is the segment output current reference pin
.IREF is supplied externally
A resistor should be connected between this pin and VSS to maintain the current around 10uA. Please refer to Figure 8-15 for the details of resistor value
5~12 D7~D0 .These pins are bi-directional data bus connecting to the MCU data bus
.Unused pins are recommended to tie LOW
.When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC
.When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL
13 #E/RD .This pin is MCU interface input
.When 6800 interface mode is selected, this pin will be used as the Enable (E) signal
.Read/write operation is initiated when this pin is pulled HIGH and the chip is selected
.When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected
.When serial or I2C interface is selected, this pin must be connected to VSS
14 #R/W .This pin is read / write control input pin connecting to the MCU interface
(#When 6800 interface mode is selected, this pin will be used as Read/Write (R/W
selection input. Read mode will be carried out when this pin is pulled HIGH and
.write mode when LOW
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data
.write operation is initiated when this pin is pulled LOW and the chip is selected
.When serial or I2C interface is selected, this pin must be connected to VSS
15 #D/C .This pin is Data/Command control pin connecting to the MCU
.When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command
.register
.In I2C mode, this pin acts as SA0 for slave address selection
.When 3-wire serial interface is selected, this pin must be connected to VSS
For detail relationship to MCU interface signals, refer to Timing Characteristics
16 #RES .This pin is reset signal input
.When the pin is pulled LOW, initialization of the chip is executed
.Keep this pin pull HIGH during normal operation
17 #CS .This pin is the chip select input connecting to the MCU
The chip is enabled for MCU communication only when CS# is pulled LOW (active
.(LOW
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the
following table.

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 Vdd Power supply pin for core logic operation
22~28 NC No connection
29 Vss .Ground pin. It must be connected to external ground
30 (NC(Vss (No connection. (ground

المواصفات العامة

العنصر الأبعاد الوحدة
مصفوفة نقطية (قة العرض) 128 × 64 نقطة
أبعاد الوحدة 77.2 × 42.14 ×3.4 mm
المنطقة النشطة 55.01 × 27.49 mm
حجم النقطة 0.40 × 0.40 mm
درجة النقطة 0.43 × 0.43 mm
وضع العرض مصفوفة موجبة
لون العرض أحادية اللون
Drive Duty 1/64 Duty
IC SSD1309
الواجهة 6800,8080,SPI,I2C
الحجم (القطر) 2.42 بوصة ‎‎

تصنيفات الحد الأقصى المطلق

Parameter الرمز أدنى قيمة أقصى قيمة الوحدة
Supply Voltage for Logic VDD -0.3 4 V
Supply Voltage for Display VCC 0 15 V
درجة حرارة التشغيل TOP -40 +80 °C
درجة حرارة التخزين TSTG -40 +85 °C

المميزات الإلكترونية

DC المميزات الإلكترونية

العنصر الرمز الحالة أدنى قيمة القيمة النموذجية أقصى قيمة الوحدة
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 12.5 13.0 13.5 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
50% Check Board operating Current VCC =13V - 29 43.5 mA

Search keyword: 128x64 oled, oled 128x64, 2.42 oled, 2.42 inch oled, oled 2.42
go top
close