Model No. WF35XSWACDNG0
►Size: 3.5 inch
►Resolution : 320x240 pixels
►View Direction : IPS
►Interface : RGB
►Driver IC : ST7272A
►Control-Board : No
►Brightness(cd/m²) : 800
►Frame Through Hole : No
►Touch Screen : Projected capacitive touch screen (PCAP)
►Touch Points: 5
►Operating Temperature: -30~+85℃ (Wide Temperature TFT)
WF35XSWACDNG0 is a 3.5-inch IPS TFT LCD display module featuring a 320x240 pixel resolution, a 24-bit RGB interface, and a projected capacitive touch panel with 5-point touch support. The display is driven by the ST7272A driver IC, while the PCAP utilizes the ILI2130 controller with an I2C interface.
The module measures 76.84 x 63.84 x 4.86 mm, with an active area of 70.08 x 52.56 mm. It features a Normally Black, transmissive TFT panel with an IPS wide viewing angle and a glare surface.
With a typical brightness of 800 cd/m² and an operating temperature range of -30℃ to +85℃, this TFT LCD display is suitable for industrial handheld devices, smart access control systems, transportation equipment, industrial control systems, and other embedded HMI applications.
| Item | Dimension | Unit |
|---|---|---|
| Size | 3.5 | inch |
| Dot Matrix | 320 x RGB x 240(TFT) | dots |
| Module dimension | 76.84(W) x 63.84(H) x 4.86(D) | mm |
| Active area | 70.08 x 52.56 | mm |
| Pixel pitch | 0.219 x 0.219 | mm |
| LCD type | TFT, normally black, Transmissive | |
| View Direction | 80/80/80/80 | |
| Driver IC | ST7272A or equivalent | |
| Interface | 24-bit RGB | |
| Aspect Ratio | 4:3 | |
| Backlight Type | LED, Normally White | |
| CTP IC | ILI2130 or equivalent | |
| CTP Interface | I2C | |
| CTP FW Version | 0x07.0x00.0x00.0x00.0x00.0x35.0x5A.0x01 | |
| CTP Resolution | 16384*16384 | |
| Touch Panel | With PCAP | |
| Surface | Glare | |
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Operating Temperature | TOP | -30 | － | +85 | ℃ |
| Storage Temperature | TST | -30 | － | +85 | ℃ |
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Supply Voltage For LCM | VCC | 3.0 | 3.3 | 3.6 | V |
| Supply Current For LCM | ICC | — | 20 | 30 | mA |
| Supply CTP | VDDT | 3.1 | 3.3 | 3.5 | V |
| ICTP | － | 45 | 68 | mA |
| Pin | Symbol | Function |
|---|---|---|
| 1 | LED- | Power for LED backlight cathode |
| 2 | LED- | Power for LED backlight cathode |
| 3 | LED+ | Power for LED backlight anode |
| 4 | LED+ | Power for LED backlight anode |
| 5 | NC | No connect |
| 6 | NC | No connect |
| 7 | NC(SPI_IIC_SEL) | No connect |
| 8 | /RESET | Hardware reset |
| 9 | NC(CS) | No connect |
| 10 | NC(SDA) | No connect |
| 11 | NC(SCL) | No connect |
| 12 | B0 | Data bus |
| 13 | B1 | Data bus |
| 14 | B2 | Data bus |
| 15 | B3 | Data bus |
| 16 | B4 | Data bus |
| 17 | B5 | Data bus |
| 18 | B6 | Data bus |
| 19 | B7 | Data bus |
| 20 | G0 | Data bus |
| 21 | G1 | Data bus |
| 22 | G2 | Data bus |
| 23 | G3 | Data bus |
| 24 | G4 | Data bus |
| 25 | G5 | Data bus |
| 26 | G6 | Data bus |
| 27 | G7 | Data bus |
| 28 | R0 | Data bus |
| 29 | R1 | Data bus |
| 30 | R2 | Data bus |
| 31 | R3 | Data bus |
| 32 | R4 | Data bus |
| 33 | R5 | Data bus |
| 34 | R6 | Data bus |
| 35 | R7 | Data bus |
| 36 | HSYNC | Horizontal sync signal, default is negative polarity. |
| 37 | VSYNC | Vertical sync signal, default is negative polarity. |
| 38 | DCLK | Dot-clock signal and oscillator source |
| 39 | NC(HDIR) | No connect |
| 40 | NC(VDIR) | No connect |
| 41 | VCC | Power Supply |
| 42 | VCC | Power Supply |
| 43 | NC | No connect |
| 44 | NC | No connect |
| 45 | NC(PARA_SERI) | No connect |
| 46 | NC(BIST_EN) | No connect |
| 47 | NC(ENPROG) | No connect |
| 48 | NC | No connect |
| 49 | NC | No connect |
| 50 | NC | No connect |
| 51 | NC(DISP) | No connect |
| 52 | DE | Data input enable. Display access is enabled when DE is “H”. |
| 53 | GND | Ground |
| 54 | GND | Ground |
| Pin | Symbol | Function |
|---|---|---|
| 1 | VSS | System ground pin of the IC. Connect to system ground. |
| 2 | VDDT | Power Supply : +3.3V |
| 3 | SCL | I2C clock input |
| 4 | NC | No connect |
| 5 | SDA | I2C data input and output |
| 6 | NC | No connect |
| 7 | /RST | External Reset, Low is active |
| 8 | NC | No connect |
| 9 | /INT | External interrupt to the host |
| 10 | VSS | System ground pin of the IC. Connect to system ground. |
By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.
