我們重視您的隱私
通過點擊「允許所有 Cookie」,代表您同意在您的設備上存儲 Cookie 以增強網站瀏覽體驗、分析網站使用情況並協助我們的行銷和網站效能優化工作。您可以在我們的隱私權政策中找到有關於此的更多資訊。
WEO128128D-CTP是一款直徑Ø1.18吋圓形OLED模組,模組中整合了電容式觸控螢幕,解析度為128x128點。此模組配備SSD1327 IC,支援4線SPI和I2C介面,典型邏輯電源電壓為3V,驅動方式為1/128。 此外,WEO128128D-CTP 型號還包括整合到模組中的 FT3268 觸控螢幕IC,支援I2C介面支援用於電容式觸控螢幕1指觸控。
這款WEO128128D搭配CTP觸控的圓形OLED顯示器非常適合智能家居/家電應用、能源系統、能源系統、通訊系統、醫療儀器等。 此OLED模組具有10,000:1的高對比度和高達160°的廣視角,確保顯示影像更清晰。模組設計工作溫度範圍為-20℃至+70℃,儲存溫度範圍為-30℃至+70℃。
項目 | 尺寸 | 單位 |
---|---|---|
點陣(解析度) | 128 x 128 | Dots |
模組尺寸 | Ø50.5 × 5.0 | mm |
檢視區域 | Ø30.0 | mm |
點大小 | 0.210 × 0.210 | mm |
點間距 | 0.235 × 0.235 | mm |
顯示模式 | 被動矩陣 | |
發光顏色 | 單色 | |
驅動方式 | 1/128 Duty | |
灰階 | 4 bits | |
IC | SSD1327 | |
介面 | 4線SPI , I2C | |
尺寸 | 1.18吋 |
CTP IC | FT3268 |
檢測點(觸控點) | 1 |
CTP 介面 | I2C |
參數 | 符號 | 最小值 | 最大值 | 單位 |
---|---|---|---|---|
工作電源電壓 | VCI | -0.3 | 3.6 | V |
邏輯電源電壓 | VDD | -0.5 | 2.75 | V |
顯示電源電壓 | VCC | -0.5 | 19.0 | V |
工作溫度 | TOP | -20 | +70 | °C |
儲存溫度 | TSTG | -30 | +70 | °C |
項目 | 符號 | 條件 | 最小值 | 典型值 | 最大值 | 單位 |
---|---|---|---|---|---|---|
工作電源電壓 | VCI | - | 2.8 | 3.0 | 3.3 | V |
顯示電源電壓 | VCC | - | 8.0 | 14.5 | 15.0 | V |
邏輯電源電壓 | VDD | - | 1.65 | - | 2.6 | V |
輸入高準位 | VIH | - | 0.8×VCI | - | VCI | V |
輸入低準位 | VIL | - | 0 | - | 0.2×VCI | V |
輸出高準位 | VOH | Iout = 100uA | 0.9×VCI | - | VCI | V |
輸出低準位 | VOL | Iout = 100uA | 0 | - | 0.1×VCI | V |
50%顯示畫面耗電流 | VCC =14.5V | - | 15 | 30 | mA |
觸控面板控制器 FT3268
項目 | 符號 | 條件 | 最小值 | 典型值 | 最大值 | 單位 |
---|---|---|---|---|---|---|
輸入高準位 | VIH | - | 0.7×VDD | - | VDD | V |
輸入低準位 | VIL | - | -0.3 | - | 0.3×VDD | V |
輸出高準位 | VOH | IOH = 0.1mA | 0.7×VDD | - | - | V |
輸出低準位 | VOL | IOL = 0.1mA | - | - | 0.3×VDD | V |
No. | 符號 | 功能說明 | ||||||
---|---|---|---|---|---|---|---|---|
1 | VSS | Ground pin. It must be connected to external ground. | ||||||
2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||
3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||
4 | VCI | Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. VCI must always set to be equivalent to or higher than VDD. |
||||||
5 | VDD | Power supply pin for core logic operation. VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances. |
||||||
6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS1 is pin select. Bus Interface selection
|
||||||
7 | IREF | This pin is the segment output current reference pin | ||||||
8 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||
9 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||
10 | DC# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, will be interpreted as data. When the pin is pulled LOW, will be transferred to a command register In I2C mode, this pin acts as SA0 for slave address selection. |
||||||
11 | D0 | When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout , SDAin in application and D0 is the serial clock input, SCL. |
||||||
12 | D1 | |||||||
13 | D2 | |||||||
14 | TP_SCK | I2C clock signal | ||||||
15 | TP_SDA | I2C data signal | ||||||
16 | TP_INT | Interrupt signal | ||||||
17 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | ||||||
18 | VSS | Ground |
通過點擊「允許所有 Cookie」,代表您同意在您的設備上存儲 Cookie 以增強網站瀏覽體驗、分析網站使用情況並協助我們的行銷和網站效能優化工作。您可以在我們的隱私權政策中找到有關於此的更多資訊。