私たちはあなたのプライバシーを大切にします
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー
WEO128128D-CTPは、Ø1.18インチの円形グラフィックOLEDディスプレイです。 モジュールの静電容量式タッチスクリーン付きいて、解像度128x128ドットで作られています。 このモジュールはSSD1327 ICに組み込まれて、4ラインSPI及びI2Cインターフェイスで、ロジック3V(標準値)にして、1/128駆動デューティの供給電圧をサポートします。 このモデルは、モジュール上のFT3268タッチパネルICに組み込まれて、容量性タッチスクリーンが一つの検出ポイントであるI2Cインターフェイスをサポートします。
CTPモデルを備えたこの円形OLED WEO128128Dはスマートホームアプリケーション、インテリジェントテクノロジーデバイス、エネルギーシステム、通信システム、医療機器等に最適です。高いコントラスト比10,000:1と最大160°の広い視野角を備えたこのOLEDモジュールは、よりクリアな表示画像を保証します。操作温度範囲は-20℃〜+ 70℃で、 保存温度範囲は-30℃~+ 70℃です。
項目 | サイズ | 単位 |
---|---|---|
ドットマトリックス(解像度) | 128 x 128 | Dots |
モジュールサイズ | Ø50.5 × 5.0 | mm |
有効エリア | Ø30.0 | mm |
ドットサイズ | 0.210 × 0.210 | mm |
ドットピッチ | 0.235 × 0.235 | mm |
表示モード | パッシブマトリクス | |
表示カラー | モノクロ | |
駆動方法 | 1/128Duty | |
グレースケール | 4 bits | |
IC | SSD1327 | |
インターフェイス | 4-line SPI , I2C | |
サイズ(対角線) | 1.18インチ |
CTP IC | FT3268 |
検出ポイント | 1 |
CTP インターフェイス | I2C |
パラメーター | 記号 | 最小値 | 最大値 | 単位 |
---|---|---|---|---|
動作電源電圧 | VCI | -0.3 | 3.6 | V |
ロジック電源電圧 | VDD | -0.5 | 2.75 | V |
Display電源電圧 | VCC | -0.5 | 19.0 | V |
動作温度 | TOP | -20 | +70 | °C |
保存温度 | TSTG | -30 | +70 | °C |
項目 | 記号 | 條件 | 最小値 | 典型値 | 最大値 | 単位 |
---|---|---|---|---|---|---|
動作電源電圧 | VCI | - | 2.8 | 3.0 | 3.3 | V |
Display電源電圧 | VCC | - | 8.0 | 14.5 | 15.0 | V |
ロジック電源電圧 | VCC | - | 1.65 | - | 2.6 | V |
高レベル入力 | VIH | - | 0.8×VCI | - | VCI | V |
低レベル入力 | VIL | - | 0 | - | 0.2×VCI | V |
高レベル出力 | VOH | Iout = 100uA | 0.9×VCI | - | VCI | V |
低レベル出力 | VOL | Iout = 100uA | 0 | - | 0.1×VCI | V |
50% Check Board operating Current | VCC =14.5V | - | 15 | 30 | mA |
項目 | 記号 | 條件 | 最小値 | 典型値 | 最大値 | 単位 |
---|---|---|---|---|---|---|
高レベル入力 | VIH | - | 0.7×VDD | - | VDD | V |
低レベル入力 | VIL | - | -0.3 | - | 0.3×VDD | V |
高レベル出力 | VOH | IOH = 0.1mA | 0.7×VDD | - | - | V |
低レベル出力 | VOL | IOL = 0.1mA | - | - | 0.3×VDD | V |
No. | 記号 | 説明 | ||||||
---|---|---|---|---|---|---|---|---|
1 | VSS | Ground pin. It must be connected to external ground. | ||||||
2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||
3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||
4 | VCI | Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. VCI must always set to be equivalent to or higher than VDD. |
||||||
5 | VDD | Power supply pin for core logic operation. VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances. |
||||||
6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS1 is pin select. Bus Interface selection
|
||||||
7 | IREF | This pin is the segment output current reference pin | ||||||
8 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||
9 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||
10 | DC# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, will be interpreted as data. When the pin is pulled LOW, will be transferred to a command register In I2C mode, this pin acts as SA0 for slave address selection. |
||||||
11 | D0 | When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout , SDAin in application and D0 is the serial clock input, SCL. |
||||||
12 | D1 | |||||||
13 | D2 | |||||||
14 | TP_SCK | I2C clock signal | ||||||
15 | TP_SDA | I2C data signal | ||||||
16 | TP_INT | Interrupt signal | ||||||
17 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | ||||||
18 | VSS | Ground |
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー