Modulo di OLED Rotondo da 1,18" con Schermo Tattile Capacitivo
Modello numero WEO128128D-CTP
►Tipo: grafico
►Struttura: COG
►Dimensione: 1.18 pollici
►128x128 a matrice di punti
►IC:SSD1327
►Alimentatore 3V
►1/128 duty
►Interfaccia: SPI, I2C
►pannello touch capacitivo (CTP)
►Punti di tocco : 1 Dito
►Colore display: Bianco / Giallo
►Support Grayscale
Descrizione
WEO128128D-CTP, un display OLED rotondo da Ø1,18", è dotato di uno schermo tattile capacitivo integrato nel modulo e vanta una risoluzione di 128x128 punti. Il modulo è equipaggiato con il chip SSD1327, che supporta un'interfaccia SPI a 4 linee e I2C, con una tensione di alimentazione logica tipica di 3V e un duty cycle di guida di 1/128. Inoltre, il modello WEO128128D-CTP include il chip FT3268 per pannelli touch integrato nel modulo, che supporta l'interfaccia I2C e presenta un singolo punto di rilevamento per lo schermo tattile capacitivo.
Questo modello di display OLED rotondo WEO128128D con CTP è ideale per applicazioni di smart home, dispositivi tecnologici intelligenti, sistemi energetici, sistemi di comunicazione, strumenti medici, ecc. Con un alto rapporto di contrasto di 10.000:1 e un ampio angolo di visione fino a 160°, questo modulo OLED garantisce immagini visualizzate più nitide. Il modulo è progettato per funzionare a temperature comprese tra -20℃ e +70℃, con temperature di stoccaggio che vanno da -30℃ a +70℃.
DISEGNO
Data source ref: WEO128128DWPP3D00003SPECIFICHE TECNICHE
Funzione dei Pin di Interfaccia
No. | Simbolo | Funzione | ||||||
---|---|---|---|---|---|---|---|---|
1 | VSS | Ground pin. It must be connected to external ground. | ||||||
2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||
3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||
4 | VCI | Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. VCI must always set to be equivalent to or higher than VDD. |
||||||
5 | VDD | Power supply pin for core logic operation. VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances. |
||||||
6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS1 is pin select. Bus Interface selection
|
||||||
7 | IREF | This pin is the segment output current reference pin | ||||||
8 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||
9 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||
10 | DC# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, will be interpreted as data. When the pin is pulled LOW, will be transferred to a command register In I2C mode, this pin acts as SA0 for slave address selection. |
||||||
11 | D0 | When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout , SDAin in application and D0 is the serial clock input, SCL. |
||||||
12 | D1 | |||||||
13 | D2 | |||||||
14 | TP_SCK | I2C clock signal | ||||||
15 | TP_SDA | I2C data signal | ||||||
16 | TP_INT | Interrupt signal | ||||||
17 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | ||||||
18 | VSS | Ground |
Dati meccanici
Articolo | Dimensioni | Unità |
---|---|---|
A matrice di punti | 128 x 128 | Dots |
Dimensione del modulo | Ø50.5 × 5.0 | mm |
Area attiva | Ø30.0 | mm |
Dimensioni del Dot | 0.210 × 0.210 | mm |
Passo del Dot | 0.235 × 0.235 | mm |
Modalità display | Matrice passiva | |
Colore display | monocromatici | |
Drive Duty | 1/128Duty | |
Gray Scale | 4 bits | |
IC | SSD1327 | |
Interfaccia | 4-line SPI , I2C | |
Dimensione (Diagonale) | 1.18 pollici |
CTP IC | IT7259 |
Punti di tocco | 1 |
CTP Interfaccia | I2C |
Valori massimi assoluti
Parameter | Simbolo | Valore Min | Valore massimo | Unità |
---|---|---|---|---|
Supply Voltage for Operation | VCI | -0.3 | 4.0 | V |
Supply Voltage for Logic | VDD | -0.5 | 2.75 | V |
Supply Voltage for Display | VCC | -0.5 | 19.0 | V |
Temperatura di lavoro | TOP | -20 | +70 | °C |
Temperatura di stock | TSTG | -30 | +70 | °C |
Caratteristiche elettriche
DC Caratteristiche elettriche
Articolo | Simbolo | Condizione | Valore Min | Valore tipico | Valore massimo | Unità |
---|---|---|---|---|---|---|
Supply Voltage for Operation | VCI | - | 2.8 | 3.0 | 3.3 | V |
Supply Voltage for Display | VCC | - | 8.0 | 14.5 | 15.0 | V |
Supply Voltage for Logic | VDD | - | 1.65 | - | 2.6 | V |
High Level Input | VIH | - | 0.8×VCI | - | VCI | V |
Low Level Input | VIL | - | 0 | - | 0.2×VCI | V |
High Level Output | VOH | Iout = 100uA | 0.9×VCI | - | VCI | V |
Low Level Output | VOL | Iout = 100uA | 0 | - | 0.1×VCI | V |
50% Check Board operating Current | VCC =14.5V | - | 15 | 30 | mA |
Touch Panel Controller FT3268
Articolo | Simbolo | Condizione | Valore Min | Valore tipico | Valore massimo | Unità |
---|---|---|---|---|---|---|
Input High Volt. | VIH | - | 0.7×VDD | - | VDD | V |
Input Low Volt. | VIL | - | -0.3 | - | 0.3×VDD | V |
Output High Volt. | VOH | IOH = 0.1mA | 0.7×VDD | - | - | V |
Output Low Volt. | VOL | IOL = 0.1mA | - | - | 0.3×VDD | V |
Search keyword: 128x128 oled, oled 128x128, 1.18 oled, 1.18" oled, 1.18 pollici oled, oled 1.18 pollici, oled 1.18"