Home Prodotti Display OLED Manopola OLED WEO012864Z

Ø0.96 pollici 128×64 Manopola OLED

Modello numero WEO012864Z

►Tipo: grafico
►Struttura: COG
►Dimensione: 0.96 pollici
►128x64 a matrice di punti
►A bordo Controllore SSD1306
►Alimentatore 3V
►1/64 duty
►Interfaccia: SPI, I2C
►Colore display: Bianco / Giallo / Blu

DESCRIZIONE

DISEGNO

Ø 0.96" 128×64 OLED Knob - WEO012864Z
 

Data source ref: WEO012864ZLPP3N00000

SPECIFICHE TECNICHE

Funzione dei Pin di Interfaccia

Pin No. Simbolo Funzione
1 VSS Ground pin.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
4 VCI Power supply pin for core logic operation
5 NC No connection
6 BS1 MCU bus interface selection pins.
Select appropriate logic setting as described in the following table.
  BS1
I2C 1
4-wire Serial 0
Note
(1) 0 is connected to VSS
(2) 1 is connected to VCI
7 IREF This is segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at a maximum of 30uA.
8 CS# This pin is the chip select input. (active LOW).
9 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin HIGH during normal operation.
10 D/C# When 4-wire serial interface is selected, this pin is Data/Command control pin connecting to the MCU.
In I2C mode, this pin acts as SA0 for slave address selection.
11 D0 These pins are bi-directional data bus connecting to the MCU data bus.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
12 D1
13 D2
14 NC No connection
15 NC No connection
16 NC No connection
17 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
18 VSS Ground pin.
 

Encoder PIN Definition

No. Simbolo Funzione
1 FSW_A Encoder terminal signal-A
2 FSW_B Encoder terminal signal-B
3 FSW_C Encoder terminal signal-C
4 FSW_D Ground

Dati meccanici

Articolo Dimensioni Unità
A matrice di punti 128 x 64 Dots
Dimensione del modulo Ø39.4 x 24.8 mm
Area attiva 21.74 x 10.86 mm
Dimensioni del Dot 0.148 x 0.148 mm
Passo del Dot 0.17 x 0.17 mm
Modalità display Matrice passiva
Colore display monocromatici
Drive Duty 1/64
IC SSD1326
Interfaccia 4-line SPI , I2C
Dimensione (Diagonale) 0.96 pollici

Valori massimi assoluti

Articolo Simbolo Valore Min Valore massimo Unità
Supply Voltage VCI -0.3 4.0 V
Supply Voltage for Display VCC 0 15 V
Temperatura di lavoro TOP -20 +70 °C
Temperatura di stock TST -30 +80 °C

Caratteristiche elettriche

DC Caratteristiche elettriche

Articolo Simbolo Condizione Valore Min Valore tipico Valore massimo Unità
Supply Voltage VCI 1.65 3.0 3.3 V
Supply Voltage for Display VCC 6 10 10.5 V
Input High Volt. VIH 0.8xVCI V
Input Low Volt. VIL 0.2xVCI V
Output High Volt. VOH Iout = 100uA 0.9xVCI V
Output Low Volt. VOL Iout = 100uA 0.1xVCI V
Operating Current for VCC (VCC Supplied Externally) ICC VCC =10V 5 10 mA

Search keyword: 128x64 oled, oled 128x64, 0.96 oled, 0.96" oled, 0.96 pollici oled, oled 0.96 pollici, oled 0.96"

go top
close