0.91" 128x32, I2C Moduli OLED
Modello numero WEO012832F
►Thinner version OLED
►Tipo: grafico
►Struttura: COG
►Dimensione: 0.91 pollici
►128 x 32 a matrice di punti
►IC:SSD1306
►Alimentatore 3V
►1/32 duty
►Interfaccia: I2C
►Colore display: Bianco / Giallo / Cielo blu
DISEGNO
Data source ref: WEO012832FWPP3N00001
SPECIFICHE TECNICHE
Funzione dei Pin di Interfaccia
No. | Simbolo | Funzione |
---|---|---|
1 | C2P | Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used. |
2 | C2N | |
3 | C1P | |
4 | C1N | |
5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
6 | NC | No connection |
7 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
8 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
9 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
10 | SCL | I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin inapplication and D0 is the serial clock input, SCL. |
11 | SDA | |
12 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA. |
13 | VCOMH | Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. |
14 | VCC | Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |
Specifiche generali
Articolo | Dimensioni | Unità |
---|---|---|
A matrice di punti (Risoluzione) | 128 × 32 | punti |
Dimensione del modulo | 30.0 × 11.5 × 1.26 | mm |
Area attiva | 22.384 × 5.584 | mm |
Dimensioni del Dot | 0.152 × 0.152 | mm |
Passo del Dot | 0.175 × 0.175 | mm |
Modalità display | Matrice passiva | |
Colore display | monocromatici | |
Drive Duty | 1/32 Duty | |
IC | SSD1306 | |
Interfaccia | I2C | |
Dimensione (Diagonale) | 0.91 pollici |
Valori massimi assoluti
Parameter | Simbolo | Valore Min | Valore massimo | Unità |
---|---|---|---|---|
Supply Voltage for Logic | VDD | 0 | 4.0 | V |
Supply Voltage for Display | VCC | 0 | 16.0 | V |
Temperatura di lavoro | TOP | -40 | +80 | °C |
Temperatura di stock | TSTG | -40 | +85 | °C |
Caratteristiche elettriche
DC Caratteristiche elettriche
Articolo | Simbolo | Condizione | Valore Min | Valore tipico | Valore massimo | Unità |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 2.8 | 3.0 | 3.3 | V |
Supply Voltage for Display | VCC | - | 7 | 7.25 | 8 | V |
Input High Volt. | VIH | - | 0.8×VDD | - | VDDIO | V |
Input Low Volt. | VIL | - | 0 | - | 0.2×VDD | V |
Output High Volt. | VOH | - | 0.9×VDD | - | VDDIO | V |
Output Low Volt. | VOL | - | 0 | - | 0.1×VDD | V |
Operating Current for VCC (VCC Supplied Externally) | ICC | Vcc =7.25V | - | 7 | 11 | mA |
Search keyword: 128x32 oled, oled 128x32, 0.91 oled, 0.91" oled, 0.91 pollici oled, oled 0.91, oled 0.91"