0.91 inç 128x32 I2C OLED Ekran
Model No. WEO012832F
►Thinner version OLED
►Türü : Grafik
►Yapı : COG
►Boyut : 0,91 inç
►128 x 32 dot matrisi
►IC:SSD1306
►3V güç sağlayıcı
►1/32 görev
►Ara yüz : I2C
►OLED Rengi: Beyaz / Sarı / Gök Mavisi
Açıklama
Bu WEO012832F, 128x32 noktalardan oluşan, 0,91 inç çapraz boyutlu bir COG OLED ekrandır. Bu modülün boyutları 30x11,5 mm, aktif alan boyutu 22,384x5,584 mm’dir. Bu modül, SSD1306 IC’de yerleşiktir; I2C arayüzünü destekler.
Bu 0.91 inç I2C OLED ekran, mantık için besleme gerilimi 2,8V ile 3,3V arasındadır; tipik değer 3V, ekran için besleme gerilimi 7,25V, çalıştırma görevi 1/32’tür. Bu modül serisi -40 ℃ ile +80 ℃ arasındaki sıcaklıklarda çalışabilir; saklama sıcaklıkları -40 ℃ ile +85 ℃ arasında değişir.
ÇIZIM
Data source ref: WEO012832FWPP3N00001
AYRINTILAR
Arayüz Pin Fonksiyonlari
No. | Sembol | Fonksiyon |
---|---|---|
1 | C2P | Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used. |
2 | C2N | |
3 | C1P | |
4 | C1N | |
5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
6 | NC | No connection |
7 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
8 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
9 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
10 | SCL | I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin inapplication and D0 is the serial clock input, SCL. |
11 | SDA | |
12 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA. |
13 | VCOMH | Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. |
14 | VCC | Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |
Genel Özellikler
Kalem | Ölçü | Birim |
---|---|---|
Nokta Matrisi (Çözünürlük) | 128 × 32 | Dots |
Modül ölçüleri | 30.0 × 11.5 × 1.26 | mm |
Aktif alan | 22.384 × 5.584 | mm |
Nokta boyutu | 0.152 × 0.152 | mm |
Nokta sıklığı | 0.175 × 0.175 | mm |
Display Mode | Pasif Matrisli | |
Display Color | Monokrom | |
Drive Duty | 1/32 Duty | |
IC | SSD1306 | |
Arayüz | I2C | |
Boyut (Köşegen) | 0.91 inç |
Maksimum Değerler
Parameter | Sembol | Minumum Deger | Maksimum Deger | Birim |
---|---|---|---|---|
Supply Voltage for Logic | VDD | 0 | 4.0 | V |
Supply Voltage for Display | VCC | 0 | 16.0 | V |
Çalışma Sıcaklığı | TOP | -40 | +80 | °C |
Saklama Sıcaklığı | TSTG | -40 | +85 | °C |
Elektronik Özellikleri
DC Elektronik Özellikleri
Kalem | Sembol | Durum | Minumum Deger | Tipik Deger | Maksimum Deger | Birim |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 2.8 | 3.0 | 3.3 | V |
Supply Voltage for Display | VCC | - | 7 | 7.25 | 8 | V |
Input High Volt. | VIH | - | 0.8×VDD | - | VDDIO | V |
Input Low Volt. | VIL | - | 0 | - | 0.2×VDD | V |
Output High Volt. | VOH | - | 0.9×VDD | - | VDDIO | V |
Output Low Volt. | VOL | - | 0 | - | 0.1×VDD | V |
Operating Current for VCC (VCC Supplied Externally) | ICC | Vcc =7.25V | - | 7 | 11 | mA |
Search keyword: 128x32 oled, oled 128x32, 0.91 oled, 0.91" oled, 0.91 inç oled, oled 0.91, oled 0.91"