我们重视您的隐私
通过点击「允许所有 Cookie」，代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。
产品叙述
WEO012832F是一款COG图形0.91寸小尺寸单色PMOLED模块，非常适用于穿戴式装置显示器.WEO012832F内置SSD1306控制器IC，模块支援I2C接口，此款OLED面板外观尺寸，AA 区域和VA区尺寸与WEO012832D相同，但是两款的FPC引脚数和引脚方式与接口不相同，WEO012832D是仅使用SPI串列式介面，如需使用I2C接口请选用WEO012832F此款模块。此型号OLED模块可支持内部升压及外部供电。
WEO012832F for COG OLED模块，特点是重量轻薄，高对比，低耗电，广视角，反应速度快，适用于墙面型（wall devices）或手持式测量仪 与智慧能源系统，物联网设备，智慧电表，医疗仪器以及穿戴式装置，电子烟等等.WEO012832F模组的工作温度是-40℃至+ 80℃，储存温度-40℃至+ 85℃。
规格图
Data source ref: WEO012832FWPP3N00001
产品规格
规格说明
| 项目 | 规格 | 单位 |
|---|---|---|
| 点阵(分辨率) | 128 × 32 | Dots |
| 模块尺寸 | 30.0 × 11.5 × 1.26 | mm |
| 有效区域 | 22.384 × 5.584 | mm |
| 像素大小 | 0.152 × 0.152 | mm |
| 像素间距 | 0.175 × 0.175 | mm |
| 显示模式 | Passive Matrix 被动矩阵 | |
| 发光颜色 | 单色 | |
| 驱动方式 | 1/32 Duty | |
| IC | SSD1306 | |
| 界面 | I2C | |
| 尺寸(对角线) | 0.91 寸 | |
最大绝对额定值
| 参数 | 符号 | 最小值 | 最大值 | 单位 |
|---|---|---|---|---|
| 逻辑电源电压 | VDD | 0 | 4.0 | V |
| 显示电源电压 | VCC | 0 | 16.0 | V |
| 工作温度 | TOP | -40 | +80 | °C |
| 储存温度 | TSTG | -40 | +85 | °C |
电气特性
DC 电气特性
| 项目 | 符号 | 条件 | 最小值 | 典型值 | 最大值 | 单位 |
|---|---|---|---|---|---|---|
| 逻辑电源电压 | VDD | － | 2.8 | 3.0 | 3.3 | V |
| 显示电源电压 | VCC | － | 7 | 7.25 | 8 | V |
| 输入高准位 | VIH | － | 0.8×VDD | － | VDDIO | V |
| 输入低准位 | VIL | － | 0 | － | 0.2×VDD | V |
| 输出高准位 | VOH | － | 0.9×VDD | － | VDDIO | V |
| 输出低准位 | VOL | － | 0 | － | 0.1×VDD | V |
| VCC的工作电流 (VCC Supplied Externally) | ICC | Vcc =7.25V | － | 7 | 11 | mA |
Pin功能定义
| No. | 符号 | 功能说明 |
|---|---|---|
| 1 | C2P | Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used. |
| 2 | C2N | |
| 3 | C1P | |
| 4 | C1N | |
| 5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
| 6 | NC | No connection |
| 7 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
| 8 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
| 9 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
| 10 | SCL | I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin inapplication and D0 is the serial clock input, SCL. |
| 11 | SDA | |
| 12 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA. |
| 13 | VCOMH | Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. |
| 14 | VCC | Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |