1.18 inç, 128x128 Kapasitif Dokunmatik Dairesel OLED Ekran
Model No. WEO128128D-CTP
►Türü : Grafik
►Yapı : COG
►Boyut : 1.18 inç
►128x128 dot matrisi
►IC:SSD1327
►3V güç sağlayıcı
►1/128 görev
►Ara yüz : SPI, I2C
►Kapasitif dokunmatik panelle birlikte (CTP)
►Dokunma Noktaları : 1 Parmak
►OLED Rengi: Beyaz / Sarı
►Gri Tonlama Desteği
Açıklama
WEO128128D-CTP, çaprazı 1,18 inç olan popüler yuvarlak bir OLED ekran, modül içine entegre edilmiş kapasitif dokunmatik ekrana sahip, 128x128 nokta çözünürlüğe sahiptir. Modül, 4 hatlı SPI ve I2C arabirimini destekleyen SSD1327 entegre devresi ile donatılmış olup, tipik mantık besleme gerilimi 3V ve 1/128 sürücü görev döngüsüne sahiptir. Ayrıca WEO128128D-CTP modeli, modül içine entegre edilmiş FT3268 dokunmatik panel entegre devresini içermekte olup, I2C arabirimini desteklemekte ve kapasitif dokunmatik ekran için tek bir algılama noktasına sahiptir.
Bu yuvarlak OLED WEO128128D CTP modeli, akıllı ev uygulamaları, akıllı teknoloji cihazları, enerji sistemleri, iletişim sistemleri, tıbbi aletler vb. için uygundur. Bu OLED modülü, 10.000:1 yüksek kontrast oranı ve 160°'ye kadar geniş bir görüş açısına sahiptir, bu da daha net ekran görüntüleri sağlar. Modül, -20℃ ila +70℃ arasındaki sıcaklıklarda çalışabilir ve depolama sıcaklıkları -30℃ ila +70℃ aralığındadır.
ÇIZIM
Data source ref: WEO128128DWPP3D00003AYRINTILAR
Arayüz Pin Fonksiyonlari
No. | Sembol | Fonksiyon | ||||||
---|---|---|---|---|---|---|---|---|
1 | VSS | Ground pin. It must be connected to external ground. | ||||||
2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||
3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||
4 | VCI | Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. VCI must always set to be equivalent to or higher than VDD. |
||||||
5 | VDD | Power supply pin for core logic operation. VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances. |
||||||
6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS1 is pin select. Bus Interface selection
|
||||||
7 | IREF | This pin is the segment output current reference pin | ||||||
8 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||
9 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||
10 | DC# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, will be interpreted as data. When the pin is pulled LOW, will be transferred to a command register In I2C mode, this pin acts as SA0 for slave address selection. |
||||||
11 | D0 | When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout , SDAin in application and D0 is the serial clock input, SCL. |
||||||
12 | D1 | |||||||
13 | D2 | |||||||
14 | TP_SCK | I2C clock signal | ||||||
15 | TP_SDA | I2C data signal | ||||||
16 | TP_INT | Interrupt signal | ||||||
17 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | ||||||
18 | VSS | Ground |
Mekanik Veri
Kalem | Ölçü | Birim |
---|---|---|
Nokta Matrisi | 128 x 128 | Dots |
Modül ölçüleri | Ø50.5 × 5.0 | mm |
Aktif alan | Ø30.0 | mm |
Nokta boyutu | 0.210 × 0.210 | mm |
Nokta sıklığı | 0.235 × 0.235 | mm |
Display Mode | Pasif Matrisli | |
Display Color | Monokrom | |
Drive Duty | 1/128Duty | |
Gri Tonlama | 4 bits | |
IC | SSD1327 | |
Arayüz | 4-line SPI , I2C | |
Boyut (Köşegen) | 1.18 inç |
CTP IC | FT3268 |
Dokunma Noktaları | 1 |
CTP Arayüz | I2C |
Maksimum Değerler
Parameter | Sembol | Minumum Deger | Maksimum Deger | Birim |
---|---|---|---|---|
Supply Voltage for Operation | VCI | -0.3 | 4.0 | V |
Supply Voltage for Logic | VDD | -0.5 | 2.75 | V |
Supply Voltage for Display | VCC | -0.5 | 19.0 | V |
Çalışma Sıcaklığı | TOP | -20 | +70 | °C |
Saklama Sıcaklığı | TSTG | -30 | +70 | °C |
Elektronik Özellikleri
DC Elektronik Özellikleri
Kalem | Sembol | Durum | Minumum Deger | Tipik Deger | Maksimum Deger | Birim |
---|---|---|---|---|---|---|
Supply Voltage for Operation | VCI | - | 2.8 | 3.0 | 3.3 | V |
Supply Voltage for Display | VCC | - | 8.0 | 14.5 | 15.0 | V |
Supply Voltage for Logic | VDD | - | 1.65 | - | 2.6 | V |
High Level Input | VIH | - | 0.8×VCI | - | VCI | V |
Low Level Input | VIL | - | 0 | - | 0.2×VCI | V |
High Level Output | VOH | Iout = 100uA | 0.9×VCI | - | VCI | V |
Low Level Output | VOL | Iout = 100uA | 0 | - | 0.1×VCI | V |
50% Check Board operating Current | VCC =14.5V | - | 15 | 30 | mA |
Touch Panel Controller FT3268
Kalem | Sembol | Durum | Minumum Deger | Tipik Deger | Maksimum Deger | Birim |
---|---|---|---|---|---|---|
Input High Volt. | VIH | - | 0.7×VDD | - | VDD | V |
Input Low Volt. | VIL | - | -0.3 | - | 0.3×VDD | V |
Output High Volt. | VOH | IOH = 0.1mA | 0.7×VDD | - | - | V |
Output Low Volt. | VOL | IOL = 0.1mA | - | - | 0.3×VDD | V |
Search keyword: 128x128 oled, oled 128x128, 1.18 oled, 1.18" oled, 1.18 inç oled, oled 1.18 inç, oled 1.18"