Ø1.18吋 128x128 電容式觸控 OLED 旋鈕 - WEO128128D-CTP-Knob

Ø1.18吋 128x128 電容式觸控 OLED 旋鈕

型號 WEO128128D-CTP-Knob

►圓形OLED
►類型: 繪圖型
►結構: COG
►尺寸: 1.18吋
►128x128 點陣
►IC：SSD1327
►3V電源電壓
►1/128 duty
►介面: SPI, I2C
►電容式觸控面板(CTP)
►支援指數: 1指
►發光顏色: 白色 / 黃色
►支援灰階

PDF下載

索取Demo Code 產品詢問

上一個產品回分類頁

產品敘述

WEO128128D型號為圓形OLED加CTP所推出的旋鈕樣式半成品，是一款有效區域直徑Ø1.18吋，解析度128x128像素的COG OLED。模組內建 SSD1327 IC 支援4線SPI和I2C介面，Typical 邏輯電壓為3V，1/128 driving duty。模組上觸控面板內建 FT3268 IC支援I2C介面和一指觸控。此型號圓形OLED 非常適合需電容式觸控和旋鈕進行控制的產品項目使用，例如: 智能家居應用、智能技術設備、影音系統...等。模組工作溫度-20℃~+50℃；儲存溫度為-30℃~+70℃。

規格圖

1.18 inch 128x128 OLED Knob with CTP Touch Panel - WEO128128D-CTP-Knob

Data source ref: WEO128128DWPP3D00E00

產品規格

規格說明

項目	尺寸	單位
點陣(解析度)	128 x 128	Dots
模組尺寸	Ø56 × 21.56	mm
檢視區域	Ø30.0	mm
點大小	0.210 × 0.210	mm
點間距	0.235 × 0.235	mm
顯示模式	被動矩陣
發光顏色	單色
驅動方式	1/128 Duty
灰階	4 bits
IC	SSD1327
介面	4線SPI , I2C
尺寸	1.18吋

CTP IC	FT3268
檢測點(觸控點)	1
CTP 介面	I2C

最大絕對額定值

參數	符號	最小值	最大值	單位
工作電源電壓	VCI	-0.3	3.6	V
邏輯電源電壓	VDD	-0.5	2.75	V
顯示電源電壓	VCC	-0.5	19.0	V
工作溫度	TOP	-20	+70	°C
儲存溫度	TSTG	-30	+70	°C

電氣特性

DC 電氣特性

項目	符號	條件	最小值	典型值	最大值	單位
工作電源電壓	VCI	－	2.8	3.0	3.3	V
顯示電源電壓	VCC	－	8.0	14.5	15.0	V
邏輯電源電壓	VDD	－	1.65	－	2.6	V
輸入高準位	VIH	－	0.8×VCI	－	VCI	V
輸入低準位	VIL	－	0	－	0.2×VCI	V
輸出高準位	VOH	Iout = 100uA	0.9×VCI	－	VCI	V
輸出低準位	VOL	Iout = 100uA	0	－	0.1×VCI	V
50%顯示畫面耗電流		VCC =14.5V	－	15	30	mA

觸控面板控制器 FT3268

項目	符號	條件	最小值	典型值	最大值	單位
輸入高準位	VIH	－	0.7×VDD	－	VDD	V
輸入低準位	VIL	－	-0.3	－	0.3×VDD	V
輸出高準位	VOH	IOH = 0.1mA	0.7×VDD	－	－	V
輸出低準位	VOL	IOL = 0.1mA	－	－	0.3×VDD	V

Pin功能定義

No.

符號

功能說明

VSS

Ground pin. It must be connected to external ground.

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.

VCI

Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.

VDD

Power supply pin for core logic operation.
VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances.

BS1

MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS1 is pin select.
Bus Interface selection

BS1	Interface
0	4-line SPI
1	I2C

Note (1) 0 is connected to VSS (2) 1 is connected to VCI

IREF

This pin is the segment output current reference pin

CS#

This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

RES#

This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.

DC#

This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, will be interpreted as data.
When the pin is pulled LOW, will be transferred to a command register
In I2C mode, this pin acts as SA0 for slave address selection.

When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout , SDAin in application and D0 is the serial clock input, SCL.

TP_SCK

I2C clock signal

TP_SDA

I2C data signal

TP_INT

Interrupt signal

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin.

VSS

Ground