Numer modelu WEO128128D-CTP-Knob
►Typ: graficzny
►Struktura: COG
►Rozmiar: 1.18"
►128x128 matryca punktowa
►IC：SSD1327
►zasilanie 3V
►wypełnienie 1/128
►Interfejs: SPI, I2C
►pojemnościowy panel dotykowy (CTP)
►Punkty dotyku : 1 Palec
►Kolor wyświetlacza: biały / żółto
►Obsługiwana skala szarości
| Parameter | Symbol | Minimalna wartość | Maksymalna wartość | Jednostka |
|---|---|---|---|---|
| Supply Voltage for Operation | VCI | -0.3 | 3.6 | V |
| Supply Voltage for Logic | VDD | -0.5 | 2.75 | V |
| Supply Voltage for Display | VCC | -0.5 | 19.0 | V |
| Temperatura pracy | TOP | -20 | +70 | °C |
| Temperatura przechowywania | TSTG | -30 | +70 | °C |
| Rzecz | Symbol | Stan | Minimalna wartość | Typowa wartość | Maksymalna wartość | Jednostka |
|---|---|---|---|---|---|---|
| Supply Voltage for Operation | VCI | － | 2.8 | 3.0 | 3.3 | V |
| Supply Voltage for Display | VCC | － | 8.0 | 14.5 | 15.0 | V |
| Supply Voltage for Logic | VDD | － | 1.65 | － | 2.6 | V |
| High Level Input | VIH | － | 0.8×VCI | － | VCI | V |
| Low Level Input | VIL | － | 0 | － | 0.2×VCI | V |
| High Level Output | VOH | Iout = 100uA | 0.9×VCI | － | VCI | V |
| Low Level Output | VOL | Iout = 100uA | 0 | － | 0.1×VCI | V |
| 50% Check Board operating Current | VCC =14.5V | － | 15 | 30 | mA | |
| Rzecz | Symbol | Stan | Minimalna wartość | Typowa wartość | Maksymalna wartość | Jednostka |
|---|---|---|---|---|---|---|
| Input High Volt. | VIH | － | 0.7×VDD | － | VDD | V |
| Input Low Volt. | VIL | － | -0.3 | － | 0.3×VDD | V |
| Output High Volt. | VOH | IOH = 0.1mA | 0.7×VDD | － | － | V |
| Output Low Volt. | VOL | IOL = 0.1mA | － | － | 0.3×VDD | V |
| No. | Symbol | Funkcja | ||||||
|---|---|---|---|---|---|---|---|---|
| 1 | VSS | Ground pin. It must be connected to external ground. | ||||||
| 2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||
| 3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||
| 4 | VCI | Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. VCI must always set to be equivalent to or higher than VDD. |
||||||
| 5 | VDD | Power supply pin for core logic operation. VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances. |
||||||
| 6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS1 is pin select. Bus Interface selection
|
||||||
| 7 | IREF | This pin is the segment output current reference pin | ||||||
| 8 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||
| 9 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||
| 10 | DC# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, will be interpreted as data. When the pin is pulled LOW, will be transferred to a command register In I2C mode, this pin acts as SA0 for slave address selection. |
||||||
| 11 | D0 | When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout , SDAin in application and D0 is the serial clock input, SCL. |
||||||
| 12 | D1 | |||||||
| 13 | D2 | |||||||
| 14 | TP_SCK | I2C clock signal | ||||||
| 15 | TP_SDA | I2C data signal | ||||||
| 16 | TP_INT | Interrupt signal | ||||||
| 17 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | ||||||
| 18 | VSS | Ground |
| No. | Symbol | Funkcja |
|---|---|---|
| 1 | FSW_A | Encoder terminal signal-A |
| 2 | FSW_B | Encoder terminal signal-B |
| 3 | FSW_C | Encoder terminal signal-C |
| 4 | FSW_D | Ground |
| Rzecz | Wymiar | Jednostka |
|---|---|---|
| Matryca punktowa | 128 × 128 | Dots |
| Wymiary modułu | Ø56 x 21.56 | mm |
| Obszar aktywny | Ø30.0 | mm |
| Wielkość piksela | 0.210 × 0.210 | mm |
| Raster pomiędzy pikselami | 0.235 × 0.235 | mm |
| Tryb wyświetlania | matryca | |
| Kolor wyświetlacza | Monochromatyczny | |
| Drive Duty | 1/128Duty | |
| Skala szarości | 4 bits | |
| IC | SSD1327 | |
| Interfejs | 4-line SPI , I2C | |
| Rozmiar (Przekątna) | 1.18 cal | |
| CTP IC | FT3268 |
| Punkty dotyku | 1 |
| CTP Interfejs | I2C |
Klikając „Zezwól na wszystkie pliki cookie”, zgadzasz się na przechowywanie plików cookie na swoim urządzeniu w celu usprawnienia nawigacji po witrynie, analizy korzystania z witryny oraz wspierania naszych działań marketingowych i dotyczących wydajności. Więcej informacji na ten temat znajdziesz w naszej polityce. Polityka prywatności
