Model No. WEA012864AA
►Type: Graphic
►Structure: COG+PCB
►Size: 1.54 inch
►128 x 64 Dot Matrix
►IC：SSD1327
►3V Power supply
►1/64 duty
►Interface: 4-wire SPI
►Display Color: White / Yellow
►Support Grayscale
WEA012864AA is a 1.54-inch 128×64 OLED display module with an integrated PCB and SSD1327 driver IC. It supports 4-wire SPI interface with a driving duty of 1/64. The logic supply voltage ranges from 2.8V to 5.2V (typical 3.3V).
This OLED module provides 4-bit grayscale and is suitable for electronic devices, medical applications, automotive meters, and other compact systems. Typical display current at 50% pixels on is 60 mA @ 3.0V VCC. WEA012864AA operates over a temperature range of -40°C to +80°C and can be stored from -40°C to +85°C.
Data source ref: WEA012864AAWAP3N00000
| Item | Dimension | Unit |
|---|---|---|
| Dot Matrix | 128 × 64 | - |
| Module dimension | 42.4 x 38.0 x 5.96(MAX) | mm |
| Active Area | 35.05 × 17.51 | mm |
| Pixel Size | 0.249 × 0.249 | mm |
| Pixel Pitch | 0.274 × 0.274 | mm |
| Display Mode | Passive Matrix | |
| Display Color | Monochrome | |
| Drive Duty | 1/64 Duty | |
| Gray Scale | 4 bits | |
| IC | SSD1327 | |
| Interface | 4-wire SPI | |
| Size | 1.54 inch | |
| Parameter | Symbol | Min | Max | Unit |
|---|---|---|---|---|
| Supply Voltage for Logic | VCC | 2.0 | 5.5 | V |
| Operating Temperature | TOP | -40 | +80 | °C |
| Storage Temperature | TSTG | -40 | +85 | °C |
| Item | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic(3V/5V) | VCC | － | 2.8 | 3.3 | 5.2 | V |
| Input High Volt. | VIH | － | 0.8×VCC | - | VCC | V |
| Input Low Volt. | VIL | － | VSS | - | 0.2×VCC | V |
| Output High Volt. | VOH | － | 0.9×VCC | - | VCC | V |
| Output Low Volt. | VOL | － | 0 | - | 0.1×VCC | V |
| Display 50% Pixel on | ICC | VCC =3.0V | - | 60 | 120 | mA |
| No. | Symbol | Function |
|---|---|---|
| 1 | GND | This is a ground pin. |
| 2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. |
| 3 | D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. |
| 4 | D1 | |
| 5 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
| 6 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. |
| 7 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.
