5 inch TFT Panel with LCD Controller Board
Model No. WF50FTYFGDBGA
►Size : 5 inch
►Resolution : 800x480 dots
►View Direction : 80/80/80/80
►Controller IC:SSD1963
►Control-Board : Yes
►Brightness(cd/m²): 400
►Frame Through Hole : No
►Touch Panel : Projected Capacitive Touch Panel (PCAP)
►O-Film: No
Description
WF50FTYFGDBGA is a 5-inch TFT LCD with Controller Board. The module is built-in with SSD1963 driver IC, supporting 8080 MPU interfaces. It has a resolution of 800×480 dots and 400 cd/m2 brightness. The module dimension is 120.7 x 75.8 x 8.76 mm with an active area of 108.0 × 64.8 mm. The display features a glare surface with IPS 80/80/80/80 wide viewing angles.
The display has a controller board with 36 pin-out connectors. Pin no. 33 ~ 36 are defined for backlight supply; therefore, customers have no need to design extra backlight circuits. The supply voltage for LCM (VDD) is from 3.1V to 3.6V (typical value: 3.3V). The display can operate at a temperature range from -20℃ to +70 ℃, and its storage temperatures are from -30 to +80 ℃.
The display has a controller board with 36 pin-out connectors. Pin no. 33 ~ 36 are defined for backlight supply; therefore, customers have no need to design extra backlight circuits. The supply voltage for LCM (VDD) is from 3.1V to 3.6V (typical value: 3.3V). The display can operate at a temperature range from -20℃ to +70 ℃, and its storage temperatures are from -30 to +80 ℃.
DRAWING
SPECIFICATIONS
Interface
Pin | Symbol | Function |
---|---|---|
1 | GND | System round pin of the IC. Connect to system ground. |
2 | VDD | Power Supply : +3.3V |
3 | BL_E | Backlight control signal , H: On \ L: Off |
4 | D/C | Data/Command select |
5 | WR | Write strobe signal |
6 | RD | Read strobe signal |
7 | DB0 | Data bus |
8 | DB1 | Data bus |
9 | DB2 | Data bus |
10 | DB3 | Data bus |
11 | DB4 | Data bus |
12 | DB5 | Data bus |
13 | DB6 | Data bus |
14 | DB7 | Data bus |
15 | DB8 | Data bus (When select 8bits mode, this pin is NC) |
16 | DB9 | Data bus (When select 8bits mode, this pin is NC) |
17 | DB10 | Data bus (When select 8bits mode, this pin is NC) |
18 | DB11 | Data bus (When select 8bits mode, this pin is NC) |
19 | DB12 | Data bus (When select 8bits mode, this pin is NC) |
20 | DB13 | Data bus (When select 8bits mode, this pin is NC) |
21 | DB14 | Data bus (When select 8bits mode, this pin is NC) |
22 | DB15 | Data bus (When select 8bits mode, this pin is NC) |
23 | NC | No connection |
24 | PCAP_INT | PCAP_ External interrupt to the host |
25 | CS | Chip select |
26 | RST | Hardware reset |
27 | NC | No connection |
28 | NC | No connection |
29 | PCAP_SCL | I2C clock input |
30 | PCAP_SDA | I2C data input and output |
31 | PCAP_RST | PCAP_ External Reset, Low is active |
32 | NC | No connection |
33 | VLED- | VLED- for B/L LED inverter (GND) |
34 | VLED- | VLED- for B/L LED inverter (GND) |
35 | VLED+ | VLED+ for B/L LED inverter |
36 | VLED+ | VLED+ for B/L LED inverter |
General Specifications
Item | Dimension | Unit |
---|---|---|
Size | 5.0 | inch |
Dot Matrix | 800 × 3(RGB) × 480 | dots |
Module dimension | 120.7 x 75.8 x 8.76 (Max) | mm |
Active area (AA) | 108.0 × 64.8 | mm |
Pixel pitch | 0.135 x 0.135 | mm |
LCD type | TFT, Normally Black, Transmissive | |
View Direction | 80/80/80/80 | |
Aspect Ratio | 5:3 | |
Backlight Type | LED, Normally White | |
Controller IC | SSD1963 | |
TFT Interface | Digital 8080 family MPU 8bit/16bit | |
PCAP IC | ILI2130 or Equivalent | |
PCAP Interface | I2C | |
PCAP FW Version | 0x07.0x00.0x00.0x00.0xA1.0x25.0x50.0x00 | |
PCAP Resolution | 16384*16384 | |
Touch Panel | Projected Capacitive Touch Panel (PCAP) | |
Surface | Glare |
Absolute Maximum Ratings
Item | Symbol | Min | Typ | Max | Unit |
---|---|---|---|---|---|
Operating Temperature | TOP | -20 | - | +70 | ℃ |
Storage Temperature | TST | -30 | - | +80 | ℃ |
Electrical Characteristics
Item | Symbol | Min | Typ | Max | Unit |
---|---|---|---|---|---|
Supply Voltage For LCM | VDD | 3.1 | 3.3 | 3.6 | V |
Supply Current For LCM | IDD | - | 76 | 114 | mA |