Strona główna Produkty Wyświetlacz OLED Graficzne Wyświetlacz OLED WEO128128H

1.5 ", 128x128 Wyświetlacz COG OLED graficzne

Numer modelu WEO128128H

►Typ: graficzny
►Struktura: COG
►Rozmiar: 1.5"
►128 x 128 matryca punktowa
►IC:CH1120
►zasilanie 3V
►wypełnienie 1/128
►interfejs: 8080,SPI,I2C
►Kolor wyświetlacza: biały / żółto
►Support Grayscale

Opis

 

Rysunek

1.5 inch OLED, 128x128 SPI OLED Display - WEO128128H

Data source ref:WEO128128HLAP3N00000

Specyfikacja

Dane mechaniczne

Rzecz Wymiar Jednostka
Matryca punktowa 128 × 128 dots
Wymiary modułu 33.80 x 36.50 x 2.01 mm
Obszar aktywny 26.86 x 26.86 mm
Wielkość piksela 0.185 x 0.185 mm
Raster pomiędzy pikselami 0.210 x 0.210 mm
Tryb wyświetlania matryca
Kolor wyświetlacza Monochromatyczny
Drive Duty 1/128 Duty
Skala szarości 4 bits
IC CH1120
Interfejs 8080,SPI,I2C
Rozmiar (Przekątna) 1.5 calowy

Bezwzględne oceny maksymalne

Parameter Symbol Minimalna wartość Maksymalna wartość Jednostka
Supply Voltage for Logic VDD -0.3 3.5 V
Supply Voltage for Display VPP -0.3 15.0 V
Temperatura pracy TOP -40 +80 °C
Temperatura przechowywania TSTG -40 +85 °C

Parametry elektryczne

Rzecz Symbol Stan Minimalna wartość Typowa wartość Maksymalna wartość Jednostka
Supply Voltage for Logic  VDD 1.65 3.0 3.3 V
Supply Voltage for Display  VPP 8.0 14.5 15.0 V
Input High Volt. VIH 0.8×VDD VDD V
Input Low Volt. VIL GND 0.2×VDD V
Output High Volt. VOH 0.8×VDD VDD V
Output Low Volt. VOL GND 0.1×VDD V
Display 50% Pixel on IPP VPP=14.5V 20 30 mA

Funkcja pinów interfejsu

No. Symbol Funkcja
1 ESD_GND This pin should be connected to GND.
2 VPP This is the most positive voltage supply pin of the chip.
It should be supplied externally.
3 VCOMH This is a pin for the voltage output high level for common signals.
A capacitor should be connected between this pin and GND.
4 VDD Power supply for logic
5 NC No connection
6 IM1 These are the MPU interface mode select pins.
  8080 3-wire SPI 4-wire SPI I2C
IM1 1 0 0 1
IM2 1 1 0 0
These pins must be connected to “H” or “L”.
7 IM2
8 VSS Ground for logic and analog. This pin should be connected to GND externally.
9 IREF This is a segment current reference pin.
A resistor should be connected between this pin and GND.
10 CSB This pin is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
When in I2C interface, this pin is not used, so it must be connected to “L”.
11 RESB This is a reset signal input pin. When RESB is set to “L”, the settings are initialized. The reset operation is performed by the RESB signal level. This pin internal pull high.
12 A0 This is the Data/Command control pin that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pin serves as SA0 to distinguish the different address of OLED driver.
When in 3-wire interface, this pin is not used, so it must be connected to “L”.
13 WRB This is a MPU interface input pin.
When connected to an 8080 MPU, this is active LOW. This pin connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal
When in 3-wire.4-wire & I2C interface, this pin is not used, so it must be connected to “L”.
14 RDB This is a MPU interface input pin.
When connected to an 8080 series MPU, it is active LOW. This pin is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When in 3-wire.4-wire & I2C interface, this pin is not used, so it must be connected to “L”.
15 D0 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface(SPI) and I2C is selected, then D0 serves as the serial clock input pin (SCL) and D1 serves as the serial data input pin (SI). At this time, D2 to D7 are set to high impedance. D7~D2 is recommended to connect the VDD or GND. It is also allowed to leave D7~D2 unconnected.
16 D1
17 D2
18 D3
19 D4
20 D5
21 D6
22 D7
23 VPP This is the most positive voltage supply pin of the chip
It should be supplied externally.
24 ESD_GND This pin should be connected to GND.
go top
close

Cenimy twoją prywatność

Klikając „Zezwól na wszystkie pliki cookie”, zgadzasz się na przechowywanie plików cookie na swoim urządzeniu w celu usprawnienia nawigacji po witrynie, analizy korzystania z witryny oraz wspierania naszych działań marketingowych i dotyczących wydajności. Więcej informacji na ten temat znajdziesz w naszej polityce. Polityka prywatności

Cenimy twoją prywatność

Winstar i niektóre strony trzecie używają plików cookie na stronie www.winstar.com.tw. Szczegóły dotyczące rodzajów plików cookie, ich celu oraz zaangażowanych stron trzecich są opisane poniżej i w naszej Polityce plików cookie. Kliknij „Zezwól na wszystko”, aby wyrazić zgodę na korzystanie z plików cookie i uzyskać najlepsze możliwe wrażenia na naszych stronach internetowych. Możesz także ustawić preferencje lub odrzucić pliki cookie (z wyjątkiem niezbędnych plików cookie).

Zarządzaj preferencjami zgody

Zawsze aktywne
Niezbędne pliki cookie

Te ciasteczka są niezbędne, aby umożliwić Ci poruszanie się po stronie internetowej i korzystanie z jej funkcji, takich jak ustawianie preferencji prywatności, logowanie się lub wypełnianie formularzy.

Ciasteczka analityczne

Te pliki cookie, znane również jako „ciasteczka statystyczne”, zbierają informacje o tym, jak korzystasz z witryny, takie jak które strony odwiedziłeś i które linki kliknąłeś. Zobacz szczegóły.