Home محصولات ماژول OLED گرافیک OLED WEA025664A

مدل شماره WEA025664A

◄نوع: گرافیک
◄ساختار: COG+PCB
◄سایز: 2.08 اینچ
◄ماتریس نقطه ای 256×64
◄کنترلگر SSD1362
◄منبع: انرژی 3V
◄کار: 1/64
◄رابط: SPI
◄رنگ صفحه‌نمایش: سفید / زرد
◄Support Grayscale
◄Traditional Chinese version options (Font IC: GT21L16T1W)

طراحی

OLED Graphic COG+PCB, 256x64, 2.08 - WEA025664A - Winstar Display

Data source ref: WEA025664ALAP3N00000

مشخصات

عملکرد پین رابط

No. نماد عملکرد
1 GND Reserved pin. It should be connected to ground.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SID.
4 D1
5 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
6 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[1:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[1:0] will be transferred to a command register.
7 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

داده مکانیکی

مورد ابعاد واحد
وضوح 256 × 64 Dots
ابعاد ماژول 70.0 × 22.0 × 1.76 mm
ناحیه فعال 51.18 × 12.78 mm
اندازه نقطه 0.18 × 0.18 mm
درجه نقطه 0.2 × 0.2 mm
حالت رنگ Passive Matrix
رنگ صفحه‌نمایش Monochrome
Drive Duty 1/64 Duty
Gray Scale 4 Bits
IC SSD1362
رابط SPI
سایز 2.08 اینچ

بیشینه مقادیر مجاز مطلق

Parameter نماد مقدار حداقل مقدار حداکثر واحد
Supply Voltage VCC 1.65 5.5 V
دمای عملیاتی TOP -40 +80 °C
دمای بسته‌بندی TSTG -40 +85 °C

مشخصات الکترونیکی

DC مشخصات الکترونیکی

مورد نماد وضعیت مقدار حداقل مقدار معمول مقدار حداکثر واحد
Supply Voltage VCC 2.8 3.3 5.2 V
Input High Volt. VIH 0.8×VCC VCC V
Input Low Volt. VIL 0 0.2×VCC V
Output High Volt. VOH 0.9×VCC VCC V
Output Low Volt. VOL 0 0.1×VCC V
50% Check Board operating Current ICC VCC=3.3V 90 135 mA
go top
close