我们重视您的隐私
通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。
WEA025664A型号是COG结构加PCB板OLED显示器,OLED面板分辨率为256x64像素,对角线尺寸为2.08寸,PCB板上设计了2四个螺丝孔让客户固定模块更加方便。WEA025664A OLED模块搭配可支持4线SPI接口的SSD1362驱动IC,此型号您可另选支持3线SPI接口以及繁体中文字库GT21L16T1W IC版本模块,GT21L16T1W 是15x16点阵中文字库IC可支持 GB12345 标准繁体中文、BIG5 繁体中文、JIS0208 标准日语 (与Unicode兼容) 以及共150个国家字库。WEA025664A含转换电路同时适用3V~5V电压驱动,支持16灰阶(4 bits)模式,1/64 duty,以棋盘格50%画素点亮画面测试,Vdd用3.3V点亮时耗电流90mA。
WEA025664A是COG结构加PCB板OLED显示器,因OLED面板自发光无需背光特性,模块即使含PCB板仍比传统STN轻薄、低耗电流,非常适合用于智能家电、量测仪器、便携设备、智能医疗产品、个人健康检测等产品。此款模块工作温度是-40℃~+80℃,储存温度-40℃~+85℃。
项目 | 规格 | 单位 |
---|---|---|
分辨率 | 256 x 64 | Dots |
模块尺寸 | 70.0 x 22.0 x 1.76 | mm |
有效区域 | 51.18 x 12.78 | mm |
像素大小 | 0.18 x 0.18 | mm |
像素间距 | 0.2 x 0.2 | mm |
显示模式 | 被动矩阵 | |
显示颜色 | 单色 | |
驱动方式 | 1/64 Duty | |
灰阶 | 4 Bits | |
IC | SSD1362 | |
接口 | SPI | |
尺寸 | 2.08 寸 |
参数 | 符号 | 最小值 | 最大值 | 单位 |
---|---|---|---|---|
电源电压 | VCC | 1.65 | 5.5 | V |
工作温度 | TOP | -40 | +80 | °C |
储存温度 | TSTG | -40 | +85 | °C |
项目 | 符号 | 条件 | 最小值 | 典型值 | 最大值 | 单位 |
---|---|---|---|---|---|---|
电源电压 | VCC | - | 2.8 | 3.3 | 5.2 | V |
输入高电压 | VIH | - | 0.8×VCC | - | VCC | V |
输入高电压 | VIL | - | 0 | - | 0.2×VCC | V |
输出高电压 | VOH | - | 0.9×VCC | - | VCC | V |
输出低电压 | VOL | - | 0 | - | 0.1×VCC | V |
50% Check Board operating Current | ICC | VCC=3.3V | - | 90 | 135 | mA |
No. | 符号 | 功能说明 |
---|---|---|
1 | GND | Reserved pin. It should be connected to ground. |
2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. |
3 | D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SID. |
4 | D1 | |
5 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
6 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[1:0] will be interpreted as data. When the pin is pulled LOW, the data at D[1:0] will be transferred to a command register. |
7 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。