我们重视您的隐私
通过点击「允许所有 Cookie」，代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。
产品叙述
WEO012832N为COG结构2.23寸绘图型OLED显示器模块，显示画面由128x32 dots组成。此OLED模块内置SH1106，有6800 / 8080、4线 SPI 和 I2C等多种接口可选择。WEO012832N逻辑电压 typical value 3V，显示电压typical value 12V, 驱动方式 1/32 duty, 50%显示画面耗电流为15 mA@12VDD (白色)。WEO012832N型号是WEO012832A型号IC替代解决方案；电气特性和PFC引脚定义相同。客户只需调整初始代码。此型号OLED模块可支持内部升压及外部供电。
WEO012832N适用于智能家居应用、m-POS、物联网系统、智能技术设备、能源系统、通信系统、医疗仪器、电动汽车充电等。模块操作温度范围-40~+80°C；储存温度范围-40~+85°C。
规格图
Data source ref: WEO012832NWPP3N00000
产品规格
Pin功能定义
| No. | 符号 | 功能 | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | N.C.(GND) | No connection. | |||||||||||||||
| 2~3 | VSS | Ground. | |||||||||||||||
| 4 | N.C. | No connection. | |||||||||||||||
| 5 | VDD1 | Power supply input. | |||||||||||||||
| 6 | IM1 |
|
|||||||||||||||
| 7 | IM2 | ||||||||||||||||
| 8 | ___ CS |
This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled. | |||||||||||||||
| 9 | ___ RES |
This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level. | |||||||||||||||
| 10 | A0 | This is the Data/Command control pad that determines whether the data bits are data or a command. A0 = “H”: the inputs at D0 to D7 are treated as display data. A0 = “L”: the inputs at D0 to D7 are transferred to the command registers. In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver. |
|||||||||||||||
| 11 | ___ WR |
This is a MPU interface input pad. When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal. When R/W = “H”: Read. When R/W = “L”: Write. |
|||||||||||||||
| 12 | ___ E/RD |
This is a MPU interface input pad. When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”. When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU. When RD = “H”: Enable. When RD = “L”: Disable. |
|||||||||||||||
| 13~20 | D0~D7 | This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus. When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance. When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance. |
|||||||||||||||
| 21 | IREF | This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA. | |||||||||||||||
| 22 | VCOMH | This is a pad for the voltage output high level for common signals. A capacitor should be connected between this pad and VSS. |
|||||||||||||||
| 23 | VPP | OLED panel power supply. It could be supplied externally. A capacitor should be connected between this pad and VSS. |
|||||||||||||||
| 24 | NC(GND) | No connection. |
规格说明
| 项目 | 规格 | 单位 |
|---|---|---|
| 分辨率 | 128 × 32 Dots | Dots |
| 模块尺寸 | 62.0 × 24.0 × 2.17 | mm |
| 有效区域 | 55.016 × 13.096 | mm |
| 像素大小 | 0.406 × 0.386 | mm |
| 像素间距 | 0.43 × 0.41 | mm |
| 显示模式 | 被动矩阵 | |
| 显示颜色 | 单色 | |
| 驱动方式 | 1/32 Duty | |
| IC | SH1106 | |
| 接口 | 6800,8080,4线SPI,I2C | |
| 尺寸 | 2.23 寸 | |
最大绝对额定值
| 参数 | 符号 | 最小值 | 最大值 | 单位 |
|---|---|---|---|---|
| 逻辑电源电压 | VDD1-VSS | -0.3 | 3.6 | V |
| 显示电源电压 | VPP | -0.3 | 14.5 | V |
| 工作温度 | TOP | -40 | +80 | °C |
| 储存温度 | TSTG | -40 | +85 | °C |
电气特性
| 参数 | 符号 | 条件 | 最小值 | 典型值 | 最大值 | 单位 |
|---|---|---|---|---|---|---|
| 逻辑电源电压 | VDD1 | － | 1.65 | 3.0 | 3.3 | V |
| 显示电源电压 | VPP | － | 6.4 | 12.0 | 12.5 | V |
| 输入高电压 | VIH | － | 0.8XVDD1 | － | VDD1 | V |
| 输入低电压 | VIL | － | VSS | － | 0.2xVDD1 | V |
| 输出高电压 | VOH | － | 0.8xVDD1 | － | VDD1 | V |
| 输出低电压 | VOL | － | VSS | － | 0.2xVDD1 | V |
| Display 50% Pixel On | IPP | VPP=12V | － | 15 | 30 | mA |