1.1" 96x64 Графические OLED дисплей
Артикул. WEO009664B
►Тип: Графический
►Тип монтажа контроллера: COG
►Диагональ: 1.1 дюйма
►Разрешение: 96 x 64 точек
►IC：SSD1327
►3V Power supply
►1/64 duty
►Интерфейс: 6800, 8080, SPI, I2C
►Цвет дисплея: Белый / Желтый
►Инверсия
►Other FPC options available in below table
Описание
Разрешение данного PMOLED составляет 96x64 точек и сделан на базе контроллера IC SSD1327 c поддержкой интерфейсов: параллельного 6800/8080 8-Бит, I2C и четырехжильного SPI интерфейса. Напряжение питания 3V, а рабочий цикл 1/64 и работает в режиме полутонового изображения, которое имеет кодируемый 16 Бит канал яркости. OLED дисплей WEO009664B является заменой TAB OLED WEX009664A/B, который был снят с производства в связи со снятием контроллера IC. Оба модуля имеют одинаковую активную область и одинаковую диагональ дисплея. Этот 1.1" дюймовый OLED подойдет для носимых устройств, mp3, портативных устройств, персональных приборов для ухода, диктофонов, устройств медицинского назначения и т.д. WEO009664B может работать при температурах от -40 ° С до + 80 ℃; а температура хранения - от -40 ℃ до + 85 ℃.
FPC Options
Чертеж
WEO009664B with Hotbar FPC
Data source ref: WEO009664BWAP3N00H00
WEO009664B with ZIF FPC
Data source ref: WEO009664BLAP3N00000
Технические характеристики
Функции контроллера контактного интерфейса
| No. | Символы | Описание | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | VSS | Ground pin. It must be connected to external ground. | ||||||||||
| 2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||||||
| 3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||||||
| 4 | VCI | Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. VCI must always set to be equivalent to or higher than VDD. |
||||||||||
| 5 | VDD | Power supply pin for core logic operation. | ||||||||||
| 6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select. Bus Interface selection
|
||||||||||
| 7 | BS2 | |||||||||||
| 8 | VSS | Ground pin. It must be connected to external ground. | ||||||||||
| 9 | IREF | This pin is the segment output current reference pin | ||||||||||
| 10 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||||||
| 11 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
| 12 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
||||||||||
| 13 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. |
||||||||||
| 14 | E | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
||||||||||
| 15 | D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||||||
| 16 | D1 | |||||||||||
| 17 | D2 | |||||||||||
| 18 | D3 | |||||||||||
| 19 | D4 | |||||||||||
| 20 | D5 | |||||||||||
| 21 | D6 | |||||||||||
| 22 | D7 | |||||||||||
| 23 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||||||
| 24 | VSS | Ground pin. |
Механические характеристики
| Наименование | Измерения | Единица |
|---|---|---|
| Разрешение | 96 x 64 | точек |
| Габариты | 29.00 × 22.50 × 1.65 | mm |
| Активная область | 22.53 × 15.01 | mm |
| Размер пикселя | 0.205 × 0.205 | mm |
| Шаг пикселя | 0.235 × 0.235 | mm |
| Матрица | Пассивная | |
| Цвет дисплея | монохромные | |
| Рабочий цикл | 1/64 Duty | |
| IC | SSD1327 | |
| Интерфейс | 4-Wire SPI, I2C, 6800, 8080 | |
| Диагональ | 1.1 дюйма | |
Электронные характеристики
| Наименование | Символы | Кондиция | Минимальный | Типичный | Максимальный | Единица |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VCI | － | 2.8 | 3.0 | 3.3 | V |
| Supply Voltage for Display | VCC | － | 8.0 | 8.5 | 9.0 | V |
| Input High Volt. | VIH | － | 0.8×VCI | － | VCI | V |
| Input Low Volt. | VIL | － | VSS | － | 0.2×VCI | V |
| Output High Volt. | VOH | － | 0.9×VCI | － | VCI | V |
| Output Low Volt. | VOL | － | VSS | － | 0.1×VCI | V |
| 50% Check Board operating Current | ICC | VCC=8.5V | － | 13.0 | 26.0 | mA |
Абсолютные максимальные значения
| Параметр | Символы | Минимальный | Максимальный | Единица |
|---|---|---|---|---|
| Supply Voltage for Operation | VCI | -0.3 | 4.0 | V |
| Supply Voltage for Logic | VDD | -0.5 | 2.75 | V |
| Supply Voltage for Display | VCC | -0.5 | 19.0 | V |
| Operating Temperature | TOP | -40 | 80 | °C |
| Storage Temperature | TSTG | -40 | 85 | °C |
FPC Options:
| Drawing | FPC Length | PIN | Pitch | ZIF FPC or HOTBAR FPC | Interface | FPC No. | Create Date |
|---|---|---|---|---|---|---|---|
 |
25.05 | 24 | 0.5 | ZIF FPC | 4-Wire SPI, I2C, 6800, 8080 | FPC2050002411XXXXX02 | 20170602 |
 |
17.8 | 24 | 0.7 | HOTBAR | 4-Wire SPI, I2C, 6800, 8080 | FPC2070002401XXXXX00 | 20171222 |
Search keyword: 96x64 oled, oled 96x64, 1.1 oled, 1.1" oled, 1.1 дюйма oled, oled 1.1, oled 1.1"
