我们重视您的隐私
通过点击「允许所有 Cookie」，代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。
产品叙述
此款1.1寸的方形OLED显示器模块，分辨率96x64 pixels。此款模块内置SSD1327 IC，模块操作支持 6800/8080 8-bit 并行接口，I2C与4-线SPI接口，3V电压驱动，1/64 duty与支持16灰阶。此款1.1吋COG结构的 WEO009664B模块可视为2017年EOL的TAB 1.1" WEX009664A/B的替代方案，两者的AA区尺寸接近都是1.1寸薄型OLED模块。
WEO009664B是小尺寸1.1" COG结构的OLED显示器，无需背光非常轻薄，适用于携带式装置、智能医疗产品、个人健康守护追踪装置、量测仪器，智能家电、穿戴式装置等产品。此模块的工作温度是-40℃至 80℃，储存温度-40℃至 85℃。
可选 FPC
规格图
WEO009664B with Hotbar FPC
Data source ref: WEO009664BWAP3N00H00
WEO009664B with ZIF FPC
Data source ref: WEO009664BLAP3N00000
产品规格
Pin功能定义
| No. | 符号 | 功能 | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | VSS | Ground pin. It must be connected to external ground. | ||||||||||
| 2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||||||
| 3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||||||
| 4 | VCI | Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. VCI must always set to be equivalent to or higher than VDD. |
||||||||||
| 5 | VDD | Power supply pin for core logic operation. | ||||||||||
| 6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select. Bus Interface selection
|
||||||||||
| 7 | BS2 | |||||||||||
| 8 | VSS | Ground pin. It must be connected to external ground. | ||||||||||
| 9 | IREF | This pin is the segment output current reference pin | ||||||||||
| 10 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||||||
| 11 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
| 12 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
||||||||||
| 13 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. |
||||||||||
| 14 | E | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
||||||||||
| 15 | D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||||||
| 16 | D1 | |||||||||||
| 17 | D2 | |||||||||||
| 18 | D3 | |||||||||||
| 19 | D4 | |||||||||||
| 20 | D5 | |||||||||||
| 21 | D6 | |||||||||||
| 22 | D7 | |||||||||||
| 23 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||||||
| 24 | VSS | Ground pin. |
规格说明
| 项目 | 规格 | 单位 |
|---|---|---|
| 分辨率 | 96 x 64 | Dots |
| 模块尺寸 | 29.00 × 22.50 × 1.65 | mm |
| 有效区域 | 22.53 × 15.01 | mm |
| 像素大小 | 0.205 × 0.205 | mm |
| 像素间距 | 0.235 × 0.235 | mm |
| 显示模式 | 被动矩阵 | |
| 显示颜色 | 单色 | |
| 驱动方式 | 1/64 Duty | |
| IC | SSD1327 | |
| 接口 | 4线 SPI, I2C, 6800, 8080 | |
| 尺寸 | 1.1 寸 | |
电气特性
| 项目 | 符号 | 条件 | 最小值 | 典型值 | 最大值 | 单位 |
|---|---|---|---|---|---|---|
| 逻辑电源电压 | VCI | － | 2.8 | 3.0 | 3.3 | V |
| 显示电源电压 | VCC | － | 8.0 | 8.5 | 9.0 | V |
| 输入高电压 | VIH | － | 0.8×VCI | － | VCI | V |
| 输入低电压 | VIL | － | VSS | － | 0.2×VCI | V |
| 输出高电压 | VOH | － | 0.9×VCI | － | VCI | V |
| 输出低电压 | VOL | － | VSS | － | 0.1×VCI | V |
| 50% Check Board operating Current | ICC | VCC=8.5V | － | 13.0 | 26.0 | mA |
最大绝对额定值
| 参数 | 符号 | 最小值 | 最大值 | 单位 |
|---|---|---|---|---|
| 工作电源电压 | VCI | -0.3 | 4.0 | V |
| 逻辑电源电压 | VDD | -0.5 | 2.75 | V |
| 显示电源电压 | VCC | -0.5 | 19.0 | V |
| 工作温度 | TOP | -40 | 80 | °C |
| 储存温度 | TSTG | -40 | 85 | °C |
可选 FPC:
| Drawing | FPC Length | PIN | Pitch | ZIF FPC or HOTBAR FPC | Interface | FPC No. | Create Date |
|---|---|---|---|---|---|---|---|
 |
25.05 | 24 | 0.5 | ZIF FPC | 4-Wire SPI, I2C, 6800, 8080 | FPC2050002411XXXXX02 | 20170602 |
 |
17.8 | 24 | 0.7 | HOTBAR | 4-Wire SPI, I2C, 6800, 8080 | FPC2070002401XXXXX00 | 20171222 |
Search keyword: 96x64 oled, oled 96x64, 1.1 oled, 1.1" oled, 1.1寸oled, oled 1.1, oled 1.1"