display OLED quadrado 96x64 de 1,1 polegadas
Model No. WEO009664B
►Tipo: Gráfico
►Estrutura: COG
►Tamanho: 1,1 polegadas
►Matriz de pontos 96x64
►IC:SSD1327
►Alimentação 3V
►1/64 duty
►Interface: 6800, 8080, SPI, I2C
►Display Color: Branco / Amarelo
►Support Grayscale
►Other FPC options available in below table
Descrição
WEO009664B é um modulo de display Gráfico COG OLED quadrado 96x64, tamanho diagonal de 1,1 polegadas. Este modelo tem dimensão de módulo de 29x22,5 mm e tamanho de área ativa de 22,53x15,01 mm. Este módulo suporta interface paralela de 6800/8080, I2C, e SPI de 4 fios.
Esta série de display OLED 96x64 pode operar a temperaturas de -40℃ a +80℃; suas temperaturas de armazenamento variam de -40℃ a +85℃. A tensão de alimentação para lógica (VDD) é de 2,8V a 3,3V, valor típico de 3V, 1/64 para o acionamento ; relação de contraste de 10,000:1.
Este módulo é um display COG OLED de tamanho pequeno, ultra-fino, leve e com baixo consumo de energia. Ele é muito adequado para aplicações domésticas inteligentes, dispositivos medicos.
FPC Options
DRAWING
WEO009664B with Hotbar FPC
Data source ref: WEO009664BWAP3N00H00
WEO009664B with ZIF FPC
Data source ref: WEO009664BLAP3N00000
SPECIFICATIONS
Função do pino de interface
No. | Símbolo | Função | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | Ground pin. It must be connected to external ground. | ||||||||||
2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||||||
3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||||||
4 | VCI | Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. VCI must always set to be equivalent to or higher than VDD. |
||||||||||
5 | VDD | Power supply pin for core logic operation. | ||||||||||
6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select. Bus Interface selection
|
||||||||||
7 | BS2 | |||||||||||
8 | VSS | Ground pin. It must be connected to external ground. | ||||||||||
9 | IREF | This pin is the segment output current reference pin | ||||||||||
10 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||||||
11 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
12 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
||||||||||
13 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. |
||||||||||
14 | E | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
||||||||||
15 | D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||||||
16 | D1 | |||||||||||
17 | D2 | |||||||||||
18 | D3 | |||||||||||
19 | D4 | |||||||||||
20 | D5 | |||||||||||
21 | D6 | |||||||||||
22 | D7 | |||||||||||
23 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||||||
24 | VSS | Ground pin. |
Dados Mecânicos
Item | Dimensão | Unidade |
---|---|---|
Matriz de pontos | 96 x 64 | ponto |
Dimensão do módulo | 29.00 × 22.50 × 1.65 | mm |
Área ativa | 22.53 × 15.01 | mm |
Tamanho do ponto | 0.205 × 0.205 | mm |
Distância entre pontos | 0.235 × 0.235 | mm |
Modo de exibição | Passive Matrix | |
Cor de exibição | Monochrome | |
Drive Duty | 1/64 Duty | |
IC | SSD1327 | |
Interface | 4-Wire SPI, I2C, 6800, 8080 | |
Tamanho | 1,1 polegadas |
Classificações Máximas Absolutas
Item | Símbolo | Condição | Valor Min | Valor Típico | Valor Máximo | Unidade |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VCI | - | 2.8 | 3.0 | 3.3 | V |
Supply Voltage for Display | VCC | - | 8.0 | 8.5 | 9.0 | V |
Input High Volt. | VIH | - | 0.8×VCI | - | VCI | V |
Input Low Volt. | VIL | - | VSS | - | 0.2×VCI | V |
Output High Volt. | VOH | - | 0.9×VCI | - | VCI | V |
Output Low Volt. | VOL | - | VSS | - | 0.1×VCI | V |
50% Check Board operating Current | ICC | VCC=8.5V | - | 13.0 | 26.0 | mA |
Classificações Máximas Absolutas
Parameter | Símbolo | Valor Min | Valor Máximo | Unidade |
---|---|---|---|---|
Supply Voltage for Operation | VCI | -0.3 | 4.0 | V |
Supply Voltage for Logic | VDD | -0.5 | 2.75 | V |
Supply Voltage for Display | VCC | -0.5 | 19.0 | V |
Temperatura de operação | TOP | -40 | 80 | °C |
Temperatura de armazenamento | TSTG | -40 | 85 | °C |
FPC Options:
Drawing | FPC Length | PIN | Pitch | ZIF FPC or HOTBAR FPC | Interface | FPC No. | Create Date |
---|---|---|---|---|---|---|---|
25.05 | 24 | 0.5 | ZIF FPC | 4-Wire SPI, I2C, 6800, 8080 | FPC2050002411XXXXX02 | 20170602 | |
17.8 | 24 | 0.7 | HOTBAR | 4-Wire SPI, I2C, 6800, 8080 | FPC2070002401XXXXX00 | 20171222 |