Home Products TFT LCD IPS TFT LCD WF0154ATAAA4DSN0

TFT Square LCD Display, 240x240, IPS, 1.54"

Model No. WF0154ATAAA4DSN0

►Square TFT Display
►1.54 inch TFT LCD
►Resolution : 240x240 dots
►View Direction :80/80/80/80 (IPS)
►Interface :SPI
►Driver IC : ST7789T3-G4-1
►Control-Board : No
►Brightness (cd/m²): 380
►Frame Through Hole : No
►Touch Screen : Without Touch Panel

Description

WF0154ATAAA4DSN0 is a TFT-LCD with a 1.54-inch diagonal square screen and a resolution of 240x240 pixels. This square LCD screen adopts an IPS panel, which has the advantages of higher contrast, a full black background when the display or pixel is off, and wider viewing angles of Left:80 / Right:80 / Up:80 / Down:80 degrees (typical), 900:1 contrast ratio (typical value), 380 nits brightness (typical value), and an anti-glare glass surface.

This module is built-in with ST7789T3-G4-1 driver IC that can communicate via SPI interfaces. The supply voltage of analog is from 2.4V to 3.3V, with a typical value of 2.8V. It can operate at the temperature range from -10℃ to +60℃, and its storage temperature range is from -20℃ to +70℃. This 1.54-inch display module is suited for wireless microphone system, coffee scale, personal, and pulse oximeters.

 
Square LCD Screen, Square Screen TFT, ST7789T3-G4-1 - WF0154ATAAA4DSN0

DRAWING

Square LCD Screen, Square Screen TFT, ST7789T3-G4-1 - WF0154ATAAA4DSN0

SPECIFICATIONS

Interface

LCM PIN Definition

Pin No. Symbol Function
1 GND Ground.
2 IOVCC Power Supply for I/O System
3 CS Chip selection pin
4 RESET This signal will reset the device
5 RS Display data/command selection pin in 4-line serial interface
6 GND Ground.
7 SCL This pin is used to be serial interface clock
8 SDA SPI interface input/output pin
9 GND Ground.
10 VDD Power Supply for Analog
11 FMARK Tearing effect signal is used to synchronize MCU to frame
memory writing.
12 VLED- Power Supply For LED Backlight Cathode Input
13 VLED- Power Supply For LED Backlight Cathode Input.
14 VLED+ Power Supply For LED Backlight Anode Input.
15 VLED+ Power Supply For LED Backlight Anode Input.

General Specifications

Item Dimension Unit
Size 1.54 inch
Dot Matrix 240 × RGB × 240 dots
Module dimension 31.52 × 33.72 × 1.94 mm
Active area 27.72 × 27.72 mm
Pixel pitch 0.1155 × 0.1155 mm
LCD type TFT, Normally Black, Transmissive
Viewing Angle 80/80/80/80
Backlight Type LED, Normally White
Drive IC ST7789T3-G4-1 or Equivalent
TFT Interface SPI
Touch Panel Without Touch Panel
Surface Anti-Glare

Absolute Maximum Ratings

Item Symbol Min Typ Max Unit
Operating Temperature TOP -10 +60
Storage Temperature TST -20 +70

Electrical Characteristics

Parameter Symbol Value Unit
Min. Typ. Max.
Analog Supply Voltage VDD 2.4 2.8 3.3 V
Power Supply for I/O System IOVCC 1.65 1.8 3.3 V
Input High Voltage VIH 0.7 IOVCC - IOVCC V
Input Low Voltage VIL GND - 0.3 IOVCC mA
Output High Voltage VoH 0.8 IOVCC - IOVCC mA
Output Low Voltage VoL GND - 0.2 IOVCC W
(Panel+LSI) Power Consumption Black Mode - 6.0 - mA
Sleeping Mode - 0.015 - mA

Search keyword: tft 1.54", 1.54 tft lcd, 1.54" tft lcd, 1.54 inch tft lcd, tft lcd 1.54, 1.54 tft display, 1.54" tft display, 1.54 inch tft display, tft display 1.54"
go top
close