Model No. WF0096ATYAA3DNF10
►0.96" ST7735 80x160 TFT Display
►Size: 0.96 inch
►Resolution : 80×160 pixels
►View Direction: IPS
►Interface: SPI
►Driver IC：ST7735S
►Control-Board : No
►Brightness(cd/m²): 400
►Frame Through Hole: No
►Touch Screen : Projected Capacitive Touch Panel (PCAP) + Optical Bonding
►Touch Points: 1
WF0096ATYAA3DNF10 is a 0.96-inch IPS TFT LCD with an 80x160 resolution and a projected capacitive touch panel (PCAP). The IPS panel provides wide viewing angles of 80/80/80/80 degrees (typical) and is designed for portrait orientation. The PCAP is bonded to the TFT using optically clear adhesive (OCA), eliminating the air gap between the touch panel and display to reduce internal reflections while providing a fully bonded display structure.
The TFT is driven by the ST7735S controller IC and supports a 4-wire SPI interface. The PCAP uses the FT3267 touch controller, supports an I2C interface, and provides single-point touch. The supply voltage (VCC) ranges from 3.0V to 3.6V. Typical brightness is 400 cd/m², with a contrast ratio of 800:1.
WF0096ATYAA3DNF10 is suitable for compact applications such as wearable devices and medical devices. The operating temperature range is -20°C to +70°C, and the storage temperature range is -30°C to +80°C.
| Item | Dimension | Unit |
|---|---|---|
| Size | 0.96 | inch |
| Dot Matrix | 80 × RGB × 160(TFT) | dots |
| Module dimension | 18.7(W) × 31.9(H) × 2.64(D) | mm |
| Active area | 10.8 × 21.696 | mm |
| Dot pitch | 0.135 × 0.1356 | mm |
| LCD type | TFT, Normally black, Transmissive | |
| Viewing Angle | 80/80/80/80(IPS) | |
| Aspect Ratio | 1:2 | |
| IC | ST7735S or equivalent | |
| TFT Interface | SPI | |
| Backlight Type | LED, Normally White | |
| CTP Interface | I2C | |
| CTP IC | FT3267 or equivalent | |
| CTP FW Version | V06 | |
| Touch Panel | Projected Capacitive Touch Screen | |
| Surface | Glare | |
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Operating Temperature | TOP | -20 | － | +70 | ℃ |
| Storage Temperature | TST | -30 | － | +80 | ℃ |
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Supply Voltage | VCC | 3.0 | 3.3 | 3.6 | V |
| Supply LCM current | ICC | － | 2 | 3 | mA |
| Supply CTP | VDDT | 2.8 | － | 3.3 | V |
| I VDDT | － | 2 | 3 | mA |
| Parameter | Symbol | Min. | Typ. | Max. | Unit |
|---|---|---|---|---|---|
| LED current | ILED | － | 20 | － | mA |
| LED voltage | VLED | 2.8 | 3.0 | 3.2 | V |
| LED Life Time | 50000 | － | － | Hr |
| Pin | Symbol | Function |
|---|---|---|
| 1 | SPI4W | SPI4W='0' , 3-wire SPI. SPI4W='1' , 4-wire SPI. |
| 2 | NC | No connection |
| 3 | SDA | Serial interface data |
| 4 | SCL | Serial interface clock |
| 5 | RS | Data/command selection pin (4-wire SPI use) |
| 6 | RES | Reset pin (low active) |
| 7 | CS | Chip selection pin (low active) |
| 8 | GND | Ground |
| 9 | NC | No connection |
| 10 | VCC | Power supply |
| 11 | LEDK | Back light cathode |
| 12 | LEDA | Back light anode |
| 13 | GND | Ground |
| Pin | Symbol | Function |
|---|---|---|
| 1 | VDDT | Power supply |
| 2 | SCL | IIC clock signal. Must be pulled high |
| 3 | SDA | IIC data signal. Must be pulled high. |
| 4 | INT | External interrupt to the host |
| 5 | RESET | External Reset. Low is active |
| 6 | VSS | Power ground. |
By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.
