10.2" TFT with TFT LCD Controller Board
Model No. WF102QTIFGDBN0
►Size : 10.2 inch
►Resolution : 800 x 480 dots
►View Direction : 12H
►Interface : MCU
►Controller IC：SSD1963
►Control-Board : Yes
►Brightness(cd/m2) : 350
►Frame Through Hole : No
►Touch Screen : No
Description
The WF102QTIFGDBN0 is a 10.2-inch TFT LCD display module with a control board. This display is with the module dimension of 235.0 x 145.8mm and AA size of 222 x 132.48 mm. It boasts a resolution of 800 x 480 pixels and an aspect ratio of 16:9. Equipped with an SSD1963 controller board, it offers interface options of 8-bit or 16-bit within the 8080 family MPU. Pin numbers 33 to 36 are designated for backlight supply, eliminating the need for an extra backlight circuit. The module features frame through holes for convenient mounting and usage.
The Winstar Q series supports the SSD1963 controller, which utilizes traditional inputs and drives TFT via VESA signal. Consequently, there's no need for a T-COM circuit onboard. Moreover, all functions, including TFT connection, backlight driver, and touch panel, are integrated into a single connection.
The WF102QTIFGDBN0 10.2-inch TFT LCD module operating temperature ranges from -20°C to +70°C, and the storage temperature ranges from -30°C to +80°C. The LCM power supply voltage is 3.0V to 3.3V, with a typical value of 3.1V. The brightness of the module is 350 nits, and the contrast ratio is 300:1 (typical value).
The key Advantages of TFT Q Series are as below:
- Winstar Q Series integrated a 36 pin-out connector on SSD1963 controller board and all connectors are the same direction.
- Q Series modules are available in 8 bit and 16 bit parallel interface options.
- The pin no. 33 ~ 36 already pre-defined as backlight supply.
- Built in backlight driver IC, Q series TFT displays can be drive by 5.0V (3.5" and 4.3"also support 3.3V). The customers do not have to change the backlight driver circuits while change the TFT module sizes.
- The 5.7", 7.0", 8.0" and 10.2" Q Series are allowed to design Sleep Mode to close BIAS(VGH, VGL, AVDD) low power consumption mode.
- Resistive Touch Screen options are available for all Q Series TFT display, and 4-Line signal (X1, Y1, X2, Y2) can be input from 36pin connector.
- Capacitive touch screen options are available for all Q Series displays, and the I2C read/write protocol can be input from the 36-pin connector.
DRAWING
SPECIFICATIONS
Interface
| Pin | Symbol | Function |
|---|---|---|
| 1 | GND | System ground pin of the IC . Connect to system ground. |
| 2 | VDD | Power Supply : +3.3V |
| 3 | BLE | Backlight control signal , H: On \ L: Off |
| 4 | D/C | Data/Command select |
| 5 | WR | Write strobe signal |
| 6 | RD | Read strobe signal |
| 7~14 | DB0~DB7 | Data bus |
| 15~22 | DB8~DB15 | Data bus (When select 8bits Mode, this pin is NC) |
| 23~24 | NC | No connect |
| 25 | CS | Chip select |
| 26 | RST | Hardware reset |
| 27 | L/R | Left / right selection; Default L/R=H |
| 28 | U/D | Up/down selection; ; Default U/D=L |
| 29~32 | NC | No connect |
| 33~34 | VLED- | Power for LED Driver IC(GND) |
| 35~36 | VLED+ | Power for LED Driver IC(+5V) |
General Specifications
| Item | Dimension | Unit |
|---|---|---|
| Size | 10.2 | inch |
| Dot Matrix | 800 × RGB × 480 | dots |
| Module dimension | 235.0(H) × 145.8(V) × 10.5(D) | mm |
| Active area | 222.0(W) × 132.48(H) | mm |
| Dot pitch | 0.0925(W) × 0.276(H) | mm |
| LCD type | TFT, Normally White, Transmissive | |
| View Direction | 12 o'clock | |
| Gray Scale Inversion Direction | 6 o'clock | |
| Backlight Type | LED, Normally White | |
| Controller IC | SSD1963 | |
| Interface | Digital 8080 family MPU 8bit/16bit | |
| Touch Panel | Without touch panel | |
| Surface | Anti-Glare | |
Absolute Maximum Ratings
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Operating Temperature | TOP | -20 | － | +70 | ℃ |
| Storage Temperature | TST | -30 | － | +80 | ℃ |
Electrical Characteristics
| Item | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Supply Voltage For LCM | VDD | － | 3.0 | 3.1 | 3.3 | V |
| Supply Current For LCM | IDD | － | － | 160 | 225 | mA |
Search keyword: tft 10.2, tft 10.2", 10.2 tft lcd, 10.2" tft lcd, 10.2 inch tft lcd, tft lcd 10.2, 10.2 tft display, 10.2" tft display, 10.2 inch tft display, tft display 10.2, tft display 10.2"
