На главную страницу Продукция COG LCD модуль WO240128A

Chip-on-Glass LCD модуль 240x128

Артикул. WO240128A

►Графический LCD
►240 x 128 точек
►IC: UC1608
►3V power supply
►1/128 duty cycle
►Интерфейс : 6800/8080/SPI


COG LCD Display 240x128 - Winstar WO240128A
Data source ref:WO240128A-TFH#

Технические характеристики

Функции контроллера контактного интерфейса

Pin No. Символы Level Описание
1 VB1- PWR LCD Bias Voltages. These are the voltage source to provide SEG driving currents. These voltages are generated internally. Connect capacitors of CBX between VBX+ and VBX–.
The resistance of these four traces directly affects the SEG driving strength of the resulting LCD module. Minimize the trace resistance is critical in achieving high quality image.
2 VB1+
3 VB0-
4 VB0+
5 VLCD PWR Main LCD Power Supply. Connect these pins together.
6 VBIAS I This is the reference voltage to generate the actual SEG driving voltage. VBIAS can be used to fine tune VLCD by external variable resistors. Internal resistor network has been provided to simplify external trimming circuit.
In COF application, connect a small bypass capacitor between VBIAS and VSS to reduce noise.
7 VSS PWR Ground
8 VDD PWR Supply Voltage for logic
9 D7 I/O Bi-directional bus for both serial and parallel host interfaces.
In serial modes, connect D[0] to SCK, D[3] to SDA,
D1 D1 D1/D5 - -
D2 D2 D2/D6 - -
D4 D4 - - -
D5 D5 - - -
D6 D6 - S9 S8/S8uc
D7 D7 0 1 1
Connect unused pins to VDD or VSS.
10 D6
11 D5
12 D4
13 D3
14 D2
15 D1
16 D0
17 WR1 I WR[1:0] controls the read/write operation of the host interface. See Host Interface section for more detail.
In parallel mode, WR[1:0] meaning depends on whether the interface is in the 6800 mode or the 8080 mode. In serial interface modes, these two pins are not used, connect them to VSS.
18 WR0
19 CD I Select Control data or Display data for read/write operation. In S9 mode, CD pin is not used. Connect CD to VSS when not used. ”L”: Control data ”H”: Display data
20 RST I When RST=”L”, all control registers are re-initialized by their default states.
Since UC1608x has built-in Power-ON-Reset and Software Reset command, RST pin is not required for proper chip operation. When RST is not used, connect the pin to VDD.
21 CS I Chip Select. The chip is selected when CS=”H”. When the chip is not selected, D[7:0] will be high impedance.
22 BM0 I Bus mode: The interface bus mode is determined by BM[1:0] and D[7:6] by the following relationship:
BM[1:0] D[7:6] Mode
11 Data 6800/8-bit
10 Data 8080/8-bit
1 0X 6800/8-bit
0 0X 8080/8-bit
1 10 3-wire SPI w/9-bit token
(S9: conventionl)
0 10 4-wire SPI w/8-bit token
(S8: conventionl)
0 11 3- or 4-wire SPI w/8-bit token
(S8uc: Ultra-Compact)
23 BM1

Механические характеристики

Наименование Измерения Единица
Разрешение 240 x 128 точек
Габариты 98.7 x 67.7 x 9.5 (Max) mm
Видимая область 92.0 x 53.0 mm
Активная область 83.975 x 44.775 mm
Размер пикселя 0.325 x0.325 mm
Шаг пикселя 0.35 x 0.35 mm
Рабочий цикл 1/128 , 1/12 Bias
Тип подсветки LED
IC UC1608
Интерфейс 6800/8080/3 wire SPI/4 wire SPI

Абсолютные максимальные значения

Наименование Символы Минимальный Типичный Максимальный Единица
Диапазон рабочих температур TOP -20 +70
Температура хранения TST -30 +80
Напряжение питания логических схем VDD -0.3 +4.0 V
LCD Generator supply voltage VDD2 -0.3 +4.0 V
LCD Generated voltage VLCD -0.3 +17.8 V

Электронные характеристики

Наименование Символы Condition Минимальный Типичный Максимальный Единица
Напряжение питания логических схем VDD-VSS 2.7 2.8~3.3 3.6 V
Напряжение питания LCM V0-VSS Ta=-20℃



Высокое входное напряжение VIH 0.8 VDD V
Низкое входное напряжение VIL 0.2VDD V
Output High Volt. VOH 0.8VDD V
Output Low Volt. VOL 0.2VDD V
Supply Current(No include LED Backlight) IDD VDD=3.0V 1.1 mA

Search keyword: 240x128 lcd, 240 x 128 lcd, lcd 240x128, lcd 240 x 128
go top