私たちはあなたのプライバシーを大切にします
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー
型番 WF24LSYAJDNN0
►2.4 インチ TFT
►解像度: 240 x 320 dots
►視野角: IPS
►インターフェース: MCU, SPI
►コントローラー IC:ILI9341V
►コントロールボード: 無
►輝度(cd/m²): 1000
►スルーホールフレーム: 無
►タッチパネル: 無
WF24LSYAJDNN0 は、240×320 の解像度を備えた 2.4 インチ縦向き IPS TFT ディスプレイモジュールです。1000ニットの高輝度により、強い外光下でも優れた視認性を提供します。全方向に 80° の広視野角と 800:1 のコントラスト比により、鮮明で安定した表示が可能です。MCU と SPI インターフェースの両方に対応し、広く使用されている ILI9341V ドライバ IC を搭載しているため、各種システムへの統合が容易です。広い動作温度範囲と 30,000 時間以上の LED 寿命により、ハンディ機器、医療機器、屋外制御パネルなどの縦向きアプリケーションに最適です。
項目 | 仕様 | 単位 |
---|---|---|
サイズ (対角線) | 2.4 | インチ |
ドットマトリックス(解像度) | 240 × RGB × 320(TFT) | dots |
外形寸法 | 42.72(W) × 60.26(H) × 2.8(D) | mm |
有効エリア | 36.72 × 48.96 | mm |
ピクセルピッチ | 0.153 × 0.153 | mm |
LCDタイプ | TFT・ノーマリ・ブラック・透過型 | |
駆動IC | ILI9341V 或いは互換性コントローラー | |
視野角度 | 80/80/80/80 | |
画面アスペクト比 | ポートレート | |
バックライトタイプ | LED・ノーマリ・ホワイト | |
タッチパネル | タッチパネル無し | |
表面処理 | グレア |
項目 | 記号 | 最小値 | 標準値 | 最大値 | 単位 |
---|---|---|---|---|---|
操作温度 | TOP | -20 | - | +70 | ℃ |
保存温度 | TST | -30 | - | +80 | ℃ |
項目 | 記号 | 最小値 | 標準値 | 最大値 | 単位 |
---|---|---|---|---|---|
アナログ電源電圧 | VCI | 2.5 | — | 3.3 | V |
ロジック電源電圧 | IOVCC | 2.5 | — | 3.3 | V |
LCM電源電圧 | ICC | — | 6 | 9 | mA |
パラメーター | 記号 | 最小値 | 標準値 | 最大値 | 単位 |
---|---|---|---|---|---|
LED電流 | — | — | 40 | — | mA |
LED電圧 | VBL+ | 10.8 | 11.6 | 12.4 | V |
LEDの寿命 | — | 30,000 | — | — | Hr |
NO | 記号 | 功能 | I/O | ||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | GND | Ground | P | ||||||||||||||||||||||||||||||||||||||||||||
2-6 | NC | No connection | - | ||||||||||||||||||||||||||||||||||||||||||||
7 | VCI | High voltage power supply for analog circuit blocks (2.5 ~ 3.3 V) |
P | ||||||||||||||||||||||||||||||||||||||||||||
8 | IOVCC | Low voltage power supply for interface logic circuits (2.5 ~ 3.3 V) |
P | ||||||||||||||||||||||||||||||||||||||||||||
9 | TE | Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low. If not used, open this pin. |
O | ||||||||||||||||||||||||||||||||||||||||||||
10 | CS | Chip select signal. | I | ||||||||||||||||||||||||||||||||||||||||||||
11 | D/CX(SCL) | (D/CX): This pin is used to select “Data or Command” in the parallel interface. When DCX = 1, data is selected. When DCX = 0, command is selected. (SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface. If not used, this pin should be connected to IOVCC or GND. |
I | ||||||||||||||||||||||||||||||||||||||||||||
12 | WR(SPI_D/C) | (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge. (D/CX) - 4-line system: Serves as the selector of command or parameter. Fix to IOVCC level when not in use. |
I | ||||||||||||||||||||||||||||||||||||||||||||
13 | RD | 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge. Fix to IOVCC level when not in use. |
I | ||||||||||||||||||||||||||||||||||||||||||||
14-29 | DB0~DB15 | 18-bit parallel bi-directional data bus for MCU system. Fix to GND level when not in use. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
30 | RESET | This signal will reset the device and must be applied to properly initialize the chip. Signal is active low. |
I | ||||||||||||||||||||||||||||||||||||||||||||
31 | IM0 | Select the MCU interface mode
If use RGB Interface must select serial interface. * : Fix this pin at IOVCC or GND. |
I | ||||||||||||||||||||||||||||||||||||||||||||
32 | IM1 | ||||||||||||||||||||||||||||||||||||||||||||||
33 | IM2 | ||||||||||||||||||||||||||||||||||||||||||||||
34 | DB16 | 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to GND level when not in use. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
35 | DB17 | ||||||||||||||||||||||||||||||||||||||||||||||
36 | VLED- | Cathode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
37 | VLED- | Cathode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
38 | VLED+ | Anode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
39 | SDA | SDA : Serial in/out signal. The data is applied on the rising edge of the SCL signal. If not used, fix this pin at IOVCC or GND. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
40 | NC | Not used, open this pin | N |
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー