우리는 귀하의 프라이버시를 소중히 여깁니다
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책
WF24LSYAJDNN0는 240x320 해상도를 제공하는 2.4인치 세로형 IPS TFT 디스플레이 모듈로, 1000니트의 고휘도를 제공하여 강한 주변광에서도 뛰어난 가독성을 보장합니다. 80도 전방향 광시야각과 800:1 명암비를 통해 선명하고 일관된 시각적 품질을 제공합니다. MCU 및 SPI 인터페이스를 모두 지원하며, 널리 사용되는 ILI9341V 드라이버 IC를 탑재해 다양한 시스템에 쉽게 통합할 수 있습니다. 넓은 동작 온도 범위와 30,000시간 이상의 LED 수명으로 인해, 휴대용 기기, 의료 장비, 실외 제어 패널 등 세로 방향 응용에 적합합니다.
항목 | 치수 | 단위 |
---|---|---|
크기 (대각선) | 2.4 | 인치 |
도트 매트릭스 (해상도) | 240 × RGB × 320(TFT) | dots |
모듈 치수 | 42.72(W) × 60.26(H) × 2.8(D) | mm |
활성 영역 | 36.72 × 48.96 | mm |
도트 피치 | 0.153 × 0.153 | mm |
LCD 유형 | TFT, 검은색, 투과성 | |
드라이버IC | ILI9341V 또는 이와 동등한 | |
시야각 | 80/80/80/80 | |
종횡비 | 세로 모드 | |
역광 타입 | LED,백색 | |
터치 패널 | 터치패널(스크린)이 없는 | |
표면 | 눈부심 |
항목 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
작동 온도 | TOP | -20 | - | +70 | ℃ |
보관 온도 | TST | -30 | - | +80 | ℃ |
항목 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
Supply Voltage For Analog | VCI | 2.5 | — | 3.3 | V |
Supply Voltage For Logic | IOVCC | 2.5 | — | 3.3 | V |
Supply Current For LCM | ICC | — | 6 | 9 | mA |
매개변수 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
LED 전류 | — | — | 40 | — | mA |
LED 전압 | VBL+ | 10.8 | 11.6 | 12.4 | V |
LED 수명 | — | 30,000 | — | — | Hr |
NO | 기호 | 기능 | I/O | ||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | GND | Ground | P | ||||||||||||||||||||||||||||||||||||||||||||
2-6 | NC | No connection | - | ||||||||||||||||||||||||||||||||||||||||||||
7 | VCI | High voltage power supply for analog circuit blocks (2.5 ~ 3.3 V) |
P | ||||||||||||||||||||||||||||||||||||||||||||
8 | IOVCC | Low voltage power supply for interface logic circuits (2.5 ~ 3.3 V) |
P | ||||||||||||||||||||||||||||||||||||||||||||
9 | TE | Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low. If not used, open this pin. |
O | ||||||||||||||||||||||||||||||||||||||||||||
10 | CS | Chip select signal. | I | ||||||||||||||||||||||||||||||||||||||||||||
11 | D/CX(SCL) | (D/CX): This pin is used to select “Data or Command” in the parallel interface. When DCX = 1, data is selected. When DCX = 0, command is selected. (SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface. If not used, this pin should be connected to IOVCC or GND. |
I | ||||||||||||||||||||||||||||||||||||||||||||
12 | WR(SPI_D/C) | (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge. (D/CX) - 4-line system: Serves as the selector of command or parameter. Fix to IOVCC level when not in use. |
I | ||||||||||||||||||||||||||||||||||||||||||||
13 | RD | 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge. Fix to IOVCC level when not in use. |
I | ||||||||||||||||||||||||||||||||||||||||||||
14-29 | DB0~DB15 | 18-bit parallel bi-directional data bus for MCU system. Fix to GND level when not in use. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
30 | RESET | This signal will reset the device and must be applied to properly initialize the chip. Signal is active low. |
I | ||||||||||||||||||||||||||||||||||||||||||||
31 | IM0 | Select the MCU interface mode
If use RGB Interface must select serial interface. * : Fix this pin at IOVCC or GND. |
I | ||||||||||||||||||||||||||||||||||||||||||||
32 | IM1 | ||||||||||||||||||||||||||||||||||||||||||||||
33 | IM2 | ||||||||||||||||||||||||||||||||||||||||||||||
34 | DB16 | 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to GND level when not in use. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
35 | DB17 | ||||||||||||||||||||||||||||||||||||||||||||||
36 | VLED- | Cathode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
37 | VLED- | Cathode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
38 | VLED+ | Anode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
39 | SDA | SDA : Serial in/out signal. The data is applied on the rising edge of the SCL signal. If not used, fix this pin at IOVCC or GND. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
40 | NC | Not used, open this pin | N |
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책