WF28JTYAJDNF0 是一款2.8吋直屏模式TFT顯示模組搭載投射電容式觸控(PCAP)，該解析度為240x320像素，亮度為400 nits(典型值)。此模組內建ILI9341 driver IC，支援MCU 或 SPI介面。WF28JTYAJDNF0擁有50.0 x 69.7mm模組尺寸，有效區域(AA)為43.2 x 57.6 mm。此顯示器的供電電源電壓為1.65V to 3.3V。投射電容式觸控螢幕整合了FT6336G IC，支援I2C介面和一指觸控。此型號的工作溫度是-20℃至+70℃，儲存溫度為-30℃至+80℃。
WF28JTYAJDNF0模組搭載IPS技術，能提供更寬的可視角度：左80/右80/上80/下80度(典型值)。TFT 顯示器中的 IPS 面板可提供更寬的視角、準確一致的色彩再現、卓越的影像品質、精確的觸控螢幕效能和一致的色溫。IPS TFT-LCD 顯示器的多功能性使其適用於各種應用，包括消費性電子產品、醫療顯示器和工業控制面板。
| NO | 符號 | 功能 | I/O | ||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | GND | Ground | P | ||||||||||||||||||||||||||||||||||||||||||||
| 2-6 | NC | No connection | - | ||||||||||||||||||||||||||||||||||||||||||||
| 7 | VCI | High voltage power supply for analog circuit blocks (2.5 ~ 3.3 V) |
P | ||||||||||||||||||||||||||||||||||||||||||||
| 8 | IOVCC | Low voltage power supply for interface logic circuits (2.5 ~ 3.3 V) |
P | ||||||||||||||||||||||||||||||||||||||||||||
| 9 | TE | Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low. If not used, open this pin. |
O | ||||||||||||||||||||||||||||||||||||||||||||
| 10 | CS | Chip select signal. | I | ||||||||||||||||||||||||||||||||||||||||||||
| 11 | D/CX(SCL) | (D/CX): This pin is used to select "Data or Command" in the parallel interface. When DCX = 1, data is selected. When DCX = 0, command is selected. (SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface. If not used, this pin should be connected to IOVCC or GND. |
I | ||||||||||||||||||||||||||||||||||||||||||||
| 12 | WR(SPI_D/C) | (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge. (D/CX) - 4-line system: Serves as the selector of command or parameter. Fix to IOVCC level when not in use. |
I | ||||||||||||||||||||||||||||||||||||||||||||
| 13 | RD | 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge. Fix to IOVCC level when not in use. |
I | ||||||||||||||||||||||||||||||||||||||||||||
| 14-29 | DB0~DB15 | 18-bit parallel bi-directional data bus for MCU system. Fix to GND level when not in use. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
| 30 | RESET | (RESX)This signal will reset the device and must be applied to properly initialize the chip. Signal is active low. |
I | ||||||||||||||||||||||||||||||||||||||||||||
| 31 | IM0 | Select the MCU interface mode
MPU Parallel interface bus and serial interface select If use RGB Interface must select serial interface. * : Fix this pin at IOVCC or GND. |
I | ||||||||||||||||||||||||||||||||||||||||||||
| 32 | IM1 | ||||||||||||||||||||||||||||||||||||||||||||||
| 33 | IM2 | ||||||||||||||||||||||||||||||||||||||||||||||
| 34 | DB16 | 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to GND level when not in use. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
| 35 | DB17 | ||||||||||||||||||||||||||||||||||||||||||||||
| 36 | LEDK | Cathode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
| 37 | LEDK | Cathode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
| 38 | LEDA | Anode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
| 39 | SDA | SDA : Serial in/out signal. The data is applied on the rising edge of the SCL signal. If not used, fix this pin at IOVCC or GND. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
| 40 | NC | Not used, open this pin | N | ||||||||||||||||||||||||||||||||||||||||||||
| Pin | 符號 | 功能 |
|---|---|---|
| 1 | VSS | Ground for analog circuit |
| 2 | VDDT | Power Supply : +3.3V |
| 3 | SCL | I2C clock input |
| 4 | NC | No connect |
| 5 | SDA | I2C data input and output |
| 6 | NC | No connect |
| 7 | /RST | External Reset, Low is active |
| 8 | NC | No connect |
| 9 | /INT | External interrupt to the host |
| 10 | VSS | Ground for analog circuit |
| 項目 | 規格 | 單位 |
|---|---|---|
| 尺寸 (對角線) | 2.8 | 吋 |
| 解析度 | 240 x RGB x 320(TFT) | dots |
| 模組尺寸 | 50.5(W) x 69.7(H) x5.67(D) | mm |
| 有效區域 (AA) | 43.2 x 57.6 | mm |
| 點間距 | 0.18 x 0.18 | mm |
| LCD類型 | TFT, 平常黑, 透射式 | |
| TFT 驅動 IC | ILI9341V 或相容IC | |
| TFT 介面 | MCU/SPI | |
| 視角 | 80/80/80/80 | |
| 長寬比 | 3:4 | |
| 背光類型 | LED ,平常白 | |
| PCAP IC | FT6336G 或相容IC | |
| PCAP 介面 | I2C | |
| PCAP FW | 0x11 | |
| 觸控面板 | 投射電容式觸控面板 (PCAP) | |
| 表面 | 亮面 | |
| 項目 | 符號 | 最小值 | 典型值 | Max | 單位 |
|---|---|---|---|---|---|
| 工作溫度 | TOP | -20 | － | +70 | ℃ |
| 儲存溫度 | TST | -30 | － | +80 | ℃ |
| 項目 | 符號 | 條件 | 最小值 | 典型值 | 最大值 | 單位 |
|---|---|---|---|---|---|---|
| 數字電源電壓 | IOVCC | － | 1.65 | － | 3.3 | V |
| 模擬電源電壓 | VCI | － | 2.5 | － | 3.3 | V |
| 觸摸邏輯的電源電壓 | VDDT | － | 3.0 | 3.3 | 3.6 | V |
| 電流電源 | ICC | IOVCC=VCI =VCC=3.0V |
－ | 13 | 20 | mA |
| 參數 | 符號 | 最小值 | 典型值 | 最大值 | 單位 |
|---|---|---|---|---|---|
| LED 電流 | － | － | 80 | － | mA |
| LED 電壓 | LEDA | 8.1 | 9.3 | 10.5 | V |
| LED 使用壽命 | － | 50000 | － | － | Hr |
By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.