2.8 pulgada Pantalla IPS 240x320 PCAP LCD TFT
Modelo Nº WF28JTYAJDNF0
►Tamaño : 2.8 pulgada
►Resolución : 240 x 320 puntos
►Dirección de la vista : IPS
►Interfaz : MCU, SPI
►Driver IC:ILI9341
►Placa de control: No
►Brillo (cd/m²): 400
►Agujero del bastidor : No
►Pantalla táctil : Con panel táctil capacitivo (PCAP)
Descripción
WF28JTYAJDNF0 es un módulo de visualización TFT de 2.8 pulgadas en modo retrato con una resolución de 240x320 píxeles, un brillo de 400 cd/m2 y una relación de contraste de 800:1. Este módulo LCD cuenta con un panel táctil capacitivo proyectado y está equipado con el circuito integrado ILI9341V, que es compatible con interfaces MCU o SPI. El módulo tiene dimensiones de 50.5 x 69.7 mm, con un área activa de 43.2 x 57.6 mm. La tensión de alimentación varía de 1.65V a 3.3V. El panel táctil capacitivo proyectado está integrado con el circuito integrado FT6336G, que es compatible con la interfaz I2C y un único punto de detección. El módulo puede operar en un rango de temperatura de -20°C a +70°C, con temperaturas de almacenamiento que van desde -30°C a +80°C.
WF28JTYAJDNF0 utiliza la tecnología IPS, ofreciendo un amplio ángulo de visión de Izquierda: 80 / Derecha: 80 / Arriba: 80 / Abajo: 80 grados (valor típico). Los paneles IPS en los displays TFT proporcionan ángulos de visión más amplios, reproducción precisa y consistente de colores, calidad de imagen superior, rendimiento preciso de la pantalla táctil y temperatura de color constante. La versatilidad de los displays TFT-LCD IPS los hace adecuados para diversas aplicaciones, incluyendo electrónica de consumo, pantallas médicas y paneles de control industriales.
DIBUJO
ESPECIFICACIONES
Función interfaz Pin
LCM PIN Definition
NO | Símbolo | Función | I/O | ||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | GND | Ground | P | ||||||||||||||||||||||||||||||||||||||||||||
2-6 | NC | No connection | - | ||||||||||||||||||||||||||||||||||||||||||||
7 | VCI | High voltage power supply for analog circuit blocks (2.5 ~ 3.3 V) |
P | ||||||||||||||||||||||||||||||||||||||||||||
8 | IOVCC | Low voltage power supply for interface logic circuits (2.5 ~ 3.3 V) |
P | ||||||||||||||||||||||||||||||||||||||||||||
9 | TE | Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low. If not used, open this pin. |
O | ||||||||||||||||||||||||||||||||||||||||||||
10 | CS | Chip select signal. | I | ||||||||||||||||||||||||||||||||||||||||||||
11 | D/CX(SCL) | (D/CX): This pin is used to select "Data or Command" in the parallel interface. When DCX = 1, data is selected. When DCX = 0, command is selected. (SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface. If not used, this pin should be connected to IOVCC or GND. |
I | ||||||||||||||||||||||||||||||||||||||||||||
12 | WR(SPI_D/C) | (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge. (D/CX) - 4-line system: Serves as the selector of command or parameter. Fix to IOVCC level when not in use. |
I | ||||||||||||||||||||||||||||||||||||||||||||
13 | RD | 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge. Fix to IOVCC level when not in use. |
I | ||||||||||||||||||||||||||||||||||||||||||||
14-29 | DB0~DB15 | 18-bit parallel bi-directional data bus for MCU system. Fix to GND level when not in use. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
30 | RESET | (RESX)This signal will reset the device and must be applied to properly initialize the chip. Signal is active low. |
I | ||||||||||||||||||||||||||||||||||||||||||||
31 | IM0 | Select the MCU interface mode
MPU Parallel interface bus and serial interface select If use RGB Interface must select serial interface. * : Fix this pin at IOVCC or GND. |
I | ||||||||||||||||||||||||||||||||||||||||||||
32 | IM1 | ||||||||||||||||||||||||||||||||||||||||||||||
33 | IM2 | ||||||||||||||||||||||||||||||||||||||||||||||
34 | DB16 | 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to GND level when not in use. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
35 | DB17 | ||||||||||||||||||||||||||||||||||||||||||||||
36 | LEDK | Cathode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
37 | LEDK | Cathode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
38 | LEDA | Anode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
39 | SDA | SDA : Serial in/out signal. The data is applied on the rising edge of the SCL signal. If not used, fix this pin at IOVCC or GND. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
40 | NC | Not used, open this pin | N |
PCAP PIN Definition
Pin | Símbolo | Función |
---|---|---|
1 | VSS | Ground for analog circuit |
2 | VDDT | Power Supply : +3.3V |
3 | SCL | I2C clock input |
4 | NC | No connect |
5 | SDA | I2C data input and output |
6 | NC | No connect |
7 | /RST | External Reset, Low is active |
8 | NC | No connect |
9 | /INT | External interrupt to the host |
10 | VSS | Ground for analog circuit |
Especificaciones generales
Elemento | Dimensión | Unidad |
---|---|---|
Tamaño (Diagonal) | 2.8 | pulgada |
Matriz de puntos (Resolución) | 240 x RGB x 320(TFT) | puntos |
Dimensión del módulo | 50.5(W) x 69.7(H) x5.67(D) | mm |
zona activa (AA) | 43.2 x 57.6 | mm |
Distancia entre puntos | 0.18 x 0.18 | mm |
Tipo de LCD | TFT, Negro, Transmisivo | |
TFT Controlador IC | ILI9341V o equivalente | |
TFT Interfaz | MCU/SPI | |
Dirección de la vista | 80/80/80/80 | |
Relación de aspecto | 3:4 | |
Tipo de retroiluminación | LED, Blanco | |
PCAP IC | FT6336G o equivalente | |
PCAP Interfaz | I2C | |
PCAP FW | 0x11 | |
panel táctil | Con panel táctil capacitivo (CTP) | |
Superficie | Deslumbramiento |
Valores nominales máximos absolutos
Elemento | Símbolo | Valor mín. | Valor típico | Valor máx. | Unidad |
---|---|---|---|---|---|
Operating Temperature | TOP | -20 | - | +70 | ℃ |
Storage Temperature | TST | -30 | - | +80 | ℃ |
Electrical Characteristics
Operating conditions
Elemento | Símbolo | Condición | Valor mín. | Valor típico | Valor máx. | Unidad |
---|---|---|---|---|---|---|
Supply Voltage for digital | IOVCC | - | 1.65 | - | 3.3 | V |
Supply Voltage for analog | VCI | - | 2.5 | - | 3.3 | V |
Supply Voltage For Touch Logic | VDDT | - | 3.0 | 3.3 | 3.6 | V |
Power Supply for Current | ICC | IOVCC=VCI =VCC=3.0V |
- | 13 | 20 | mA |
LED driving conditions
Parameter | Símbolo | Valor mín. | Valor típico | Valor máx. | Unidad |
---|---|---|---|---|---|
LED current | - | - | 80 | - | mA |
LED voltage | LEDA | 8.1 | 9.3 | 10.5 | V |
LED Life Time | - | 50000 | - | - | Hr |