我們重視您的隱私
通過點擊「允許所有 Cookie」,代表您同意在您的設備上存儲 Cookie 以增強網站瀏覽體驗、分析網站使用情況並協助我們的行銷和網站效能優化工作。您可以在我們的隱私權政策中找到有關於此的更多資訊。
WF24LTYAJDNN0是一款採用IPS面板的2.4吋TFT液晶顯示器模組。此款TFT-LCD解析度240 x 320 pixels,模組內建ILI9341V 驅動 IC,支援MCU8080與SPI介面。WF24L採用IPS面板技術,視角範圍為左: 80 / 右: 80 / 上: 80 / 下: 80 度,面板視角廣度廣,色彩鮮明、具有飽和自然的優質畫面,模組對比度800 nits,亮面玻璃,亮度500 nits(典型值)。WF24L模組為直屏模式TFT顯示器,供電電壓範圍從2.5V~3.3V。此款模組的工作溫度是-20℃ 至 +70℃,儲存溫度是 -30℃ 至 +80℃,適用於血糖血脂檢測器、空氣品質檢測器、MP3撥放器以及測速器、安全監控系統、手持設備、行車紀錄器等小型工業設備產品應用。
項目 | 規格 | 單位 |
---|---|---|
尺寸 (對角線) | 2.4 | 吋 |
解析度 | 240 × RGB × 320(TFT) | dots |
模組尺寸 | 42.72(W) × 60.26(H) × 2.8(D) | mm |
有效區域 | 36.72 × 48.96 | mm |
點間距 | 0.153 × 0.153 | mm |
LCD類型 | TFT, 平常黑, 透射式 | |
驅動IC | ILI9341V 或相容IC | |
視角 | 80/80/80/80 | |
長寬比 | Portrait | |
背光類型 | LED ,平常白 | |
觸控面板 | 無觸控面板 | |
表面 | 亮面 |
項目 | 符號 | 最小值 | 典型值 | 最大值 | 單位 |
---|---|---|---|---|---|
工作溫度 | TOP | -20 | - | +70 | ℃ |
儲存溫度 | TST | -30 | - | +80 | ℃ |
項目 | 符號 | 最小值 | 典型值 | 最大值 | 單位 |
---|---|---|---|---|---|
類比電源電壓 | VCI | 2.5 | — | 3.3 | V |
邏輯電源電壓 | IOVCC | 2.5 | — | 3.3 | V |
LCM電源電壓 | ICC | IOVCC=VCI =VCC=3.0V | 6 | 9 | mA |
NO | 符號 | 功能 | I/O |
---|---|---|---|
1 | GND | Ground | P |
2-6 | NC | No connection | - |
7 | VCI | High voltage power supply for analog circuit blocks (2.5 ~ 3.3 V) |
P |
8 | IOVCC | Low voltage power supply for interface logic circuits (2.5 ~ 3.3 V) |
P |
9 | TE | Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low. If not used, open this pin. |
O |
10 | CS | Chip select signal. | I |
11 | D/CX(SCL) | (D/CX): This pin is used to select “Data or Command” in the parallel interface. When DCX = 1, data is selected. When DCX = 0, command is selected. (SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface. If not used, this pin should be connected to IOVCC or GND. |
I |
12 | WR(SPI_D/C) | (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge. (D/CX) - 4-line system: Serves as the selector of command or parameter. Fix to IOVCC level when not in use. |
I |
13 | RD | 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge. Fix to IOVCC level when not in use. |
I |
14-29 | DB0~DB15 | 18-bit parallel bi-directional data bus for MCU system. Fix to GND level when not in use. |
I/O |
30 | RESET | This signal will reset the device and must be applied to properly initialize the chip. Signal is active low. |
I |
31 | IM0 | Select the MCU interface mode![]() MPU Parallel interface bus and serial interface select If use RGB Interface must select serial interface. * : Fix this pin at IOVCC or GND. |
I |
32 | IM1 | ||
33 | IM2 | ||
34 | DB16 | 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to GND level when not in use. |
I/O |
35 | DB17 | ||
36 | LEDK | Cathode of LED backlight. | P |
37 | LEDK | Cathode of LED backlight. | P |
38 | LEDA | Anode of LED backlight. | P |
39 | SDA | SDA : Serial in/out signal. The data is applied on the rising edge of the SCL signal. If not used, fix this pin at IOVCC or GND. |
I/O |
40 | NC | Not used, open this pin | N |
通過點擊「允許所有 Cookie」,代表您同意在您的設備上存儲 Cookie 以增強網站瀏覽體驗、分析網站使用情況並協助我們的行銷和網站效能優化工作。您可以在我們的隱私權政策中找到有關於此的更多資訊。