我們重視您的隱私
通過點擊「允許所有 Cookie」,代表您同意在您的設備上存儲 Cookie 以增強網站瀏覽體驗、分析網站使用情況並協助我們的行銷和網站效能優化工作。您可以在我們的隱私權政策中找到有關於此的更多資訊。
WF24LSYAJDNG0 是一款 2.4 吋直立向 IPS TFT 顯示器模組,解析度為 240x320 像素,具備 800 nits 高亮度,即使在不同光線環境下也能提供清晰明亮的畫面。具備全方位 80 度廣視角與 800:1 對比度,能在垂直應用中呈現鮮明穩定的影像品質。
WF24LSYAJDNG0 整合投射式電容觸控面板(PCAP),採用 CF1124 觸控控制器 IC,並支援 I²C 介面。顯示部分由廣泛使用的 ILI9341V 驅動 IC 控制,支援 80 MCU 8/16/9-bit 並列介面及 3 線 9-bit / 4 線 8-bit SPI 序列介面。LED 背光壽命超過 30,000 小時,具備廣泛的工作溫度範圍,適合用於手持裝置、可攜式醫療設備以及需直向觸控操作的戶外控制系統。
項目 | 規格 | 單位 |
---|---|---|
尺寸 (對角線) | 2.4 | 吋 |
解析度 | 240 × RGB × 320(TFT) | dots |
模組尺寸 | 42.72(W) × 60.26(H) × 4.5(D) | mm |
有效區域 | 36.72 × 48.96 | mm |
像素間距 | 0.153 × 0.153 | mm |
LCD類型 | TFT全透 | |
控制器IC | ILI9341V 或相容IC | |
視角 | 80/80/80/80 | |
長寬比 | 直屏 | |
背光類型 | LED ,平常白 | |
CTP驅動IC | CF1124或相容IC | |
CTP介面 | I2C | |
CTP FW版本 | 0x01 | |
CTP解析度 | 240 * 320 | |
觸控面板 | 投射電容式觸控面板 | |
表面 | 亮面 |
項目 | 符號 | 最小值 | 典型值 | 最大值 | 單位 |
---|---|---|---|---|---|
工作溫度 | TOP | -20 | - | +70 | ℃ |
儲存溫度 | TST | -30 | - | +80 | ℃ |
項目 | 符號 | 最小值 | 典型值 | 最大值 | 單位 |
---|---|---|---|---|---|
類比電源電壓 | VCI | 2.5 | — | 3.3 | V |
邏輯電源電壓 | IOVCC | 2.5 | — | 3.3 | V |
LCM電源電壓 | ICC | — | 6 | 9 | mA |
供應電容式觸控面板 | VDDT | 3.0 | 3.3 | 3.6 | V |
IDDT | — | 14.0 | 25.0 | mA |
參數 | 符號 | 最小值 | 典型值 | 最大值 | 單位 |
---|---|---|---|---|---|
LED電流 | — | — | 40 | — | mA |
LED電壓 | VBL+ | 10.8 | 11.6 | 12.4 | V |
LED使用壽命 | — | 30,000 | — | — | Hr |
NO | 符號 | 功能 | I/O | ||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | GND | Ground | P | ||||||||||||||||||||||||||||||||||||||||||||
2-6 | NC | No connection | - | ||||||||||||||||||||||||||||||||||||||||||||
7 | VCI | High voltage power supply for analog circuit blocks (2.5 ~ 3.3 V) |
P | ||||||||||||||||||||||||||||||||||||||||||||
8 | IOVCC | Low voltage power supply for interface logic circuits (2.5 ~ 3.3 V) |
P | ||||||||||||||||||||||||||||||||||||||||||||
9 | TE | Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low. If not used, open this pin. |
O | ||||||||||||||||||||||||||||||||||||||||||||
10 | CS | Chip select signal. | I | ||||||||||||||||||||||||||||||||||||||||||||
11 | D/CX(SCL) | (D/CX): This pin is used to select “Data or Command” in the parallel interface. When DCX = 1, data is selected. When DCX = 0, command is selected. (SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface. If not used, this pin should be connected to IOVCC or GND. |
I | ||||||||||||||||||||||||||||||||||||||||||||
12 | WR(SPI_D/C) | (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge. (D/CX) - 4-line system: Serves as the selector of command or parameter. Fix to IOVCC level when not in use. |
I | ||||||||||||||||||||||||||||||||||||||||||||
13 | RD | 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge. Fix to IOVCC level when not in use. |
I | ||||||||||||||||||||||||||||||||||||||||||||
14-29 | DB0~DB15 | 18-bit parallel bi-directional data bus for MCU system. Fix to GND level when not in use. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
30 | RESET | This signal will reset the device and must be applied to properly initialize the chip. Signal is active low. |
I | ||||||||||||||||||||||||||||||||||||||||||||
31 | IM0 | Select the MCU interface mode
If use RGB Interface must select serial interface. * : Fix this pin at IOVCC or GND. |
I | ||||||||||||||||||||||||||||||||||||||||||||
32 | IM1 | ||||||||||||||||||||||||||||||||||||||||||||||
33 | IM2 | ||||||||||||||||||||||||||||||||||||||||||||||
34 | DB16 | 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to GND level when not in use. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
35 | DB17 | ||||||||||||||||||||||||||||||||||||||||||||||
36 | VLED- | Cathode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
37 | VLED- | Cathode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
38 | VLED+ | Anode of LED backlight. | P | ||||||||||||||||||||||||||||||||||||||||||||
39 | SDA | SDA : Serial in/out signal. The data is applied on the rising edge of the SCL signal. If not used, fix this pin at IOVCC or GND. |
I/O | ||||||||||||||||||||||||||||||||||||||||||||
40 | NC | Not used, open this pin | N |
Pin | 符號 | 功能 |
---|---|---|
1 | VSS | Ground for analog circuit |
2 | VDDT | Power Supply : +3.3V |
3 | SCL | I2C clock input |
4 | NC | No connect |
5 | SDA | I2C data input and output |
6 | NC | No connect |
7 | /RST | External Reset, Low is active |
8 | NC | No connect |
9 | /INT | External interrupt to the host |
10 | VSS | Ground for analog circuit |
通過點擊「允許所有 Cookie」,代表您同意在您的設備上存儲 Cookie 以增強網站瀏覽體驗、分析網站使用情況並協助我們的行銷和網站效能優化工作。您可以在我們的隱私權政策中找到有關於此的更多資訊。