首頁 產品介紹 OLED顯示器 繪圖型 OLED 顯示器 WEO128128G

1.12吋OLED, 128x128 SPI OLED模組

型號 WEO128128G

►類型: 繪圖型
►結構: COG
►尺寸:1.12吋
►128 x 128 點陣
►IC:SH1107
►3V電源電壓
►1/128 duty
►介面: 6800,8080,4-wire SPI,I2C
►發光顏色: 白色 / 黃色

產品敘述

WEO128128G為1.12吋COG 帶Hot Bar FPC結構的繪圖型被動式OLED顯示器模組,顯示畫面由128x128像素組成。此模組內建SH1107控制器IC可支援I2C、4線SPI、6800和8080並列介面。電源電壓典型值為 3V,顯示器電源電壓典型值為12V,50%顯示畫面耗電流為15mA @ VCC 12V (白色),驅動方式為1/128 duty。

WEO0128128G COG OLED模組體積小、低功耗、輕薄,非常適合智慧電表、智能家電、POS系統、雲端/物聯網系統、手持式產品、智能設備、能源系統、車載與通訊設備以及醫療儀器等。WEO0128128G模組工作溫度為-40℃至+ 80℃,儲存溫度為-40℃至+85℃。

 

規格圖

1.12 inch OLED, 128x128 SPI OLED Display - WEO128128G
Data source ref:WEO128128GWAP3N00000

產品規格

Pin功能定義

No. 符號 功能說明
1 VPP This is the most positive voltage supply pad of the chip.
It should be supplied externally.
2 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
3 VDD Power supply for logic and input.
4 NC Not connected.
5 IM1 These are the MPU interface mode select pads.
  8080 I2C 6800 4SPI
IM1 1 1 0 0
IM2 1 0 1 0
6 IM2
7 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 15.625mA.
8 CS This pad is the chip select input. When CS = “L”, then the chip select becomes active, and data/command I/O is enabled.
9 RES This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
11 WR This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When WR = “H”: Read. When WR  = “L”: Write.
12 E/RD This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
13~20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA). At this time, D2 to D7 are set to high impedance.
21 GND Ground
22 NC Not connected.
 

規格說明

項目 規格說明 單位
點陣(解析度) 128 × 128
模組尺寸 25.9 x 30.1 x 1.26 mm
有效區域 20.076 x 20.076 mm
像素大小 0.137 x 0.137 mm
像素間距 0.157 x 0.157 mm
顯示模式 Passive Matrix 被動矩陣
顯示顏色 單色
驅動方式 1/128 Duty
IC SH1107
介面 6800,8080,4-wire SPI,I2C
尺寸 1.12 吋

最大絕對額定值

參數 符號 最小值 最大值 單位
邏輯電源電壓 VDD -0.3 3.6 V
顯示電源電壓 VPP -0.3 17.0 V
工作溫度 TOP -40 +80 °C
儲存溫度 TSTG -40 +85 °C

電氣特性

項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VDD 1.65 3.0 3.3 V
顯示電源電壓 VPP 7.0 12.0 12.5 V
輸入高電壓 VIH 0.8×VDD VDD V
輸入低電壓 VIL 0 0.2×VDD V
輸出高電壓 VOH 0.8×VDD VDD V
輸出低電壓 VOL 0 0.2×VDD V
50% Check Board operating Current IPP VPP=12V 15.0 25.0 mA


Search keyword: 128x128 oled, oled 128x128, 1.12 oled, 1.12" oled, 1.12 inch oled, oled 1.12, oled 1.12", 1.12吋oled, oled 1.12吋

go top
close