제품 OLED 디스플레이 그래픽 OLED 디스플레이 WEO128128G

1.12인치 SPI OLED 모듈

모델 번호 WEO128128G

►유형 : 그래픽
►구조 : COG
►크기 : 1.12 인치
►128 x 128 점 행렬
►IC:SH1107
►3V 전원 공급 장치
►1/128 duty
►인터페이스 : 6800,8080,4-wire SPI,I2C
►디스플레이 색상: 백색 / 노란색

설명

도면

1.12 inch OLED, 128x128 SPI OLED Display - WEO128128G
Data source ref:WEO128128GWAP3N00000

사양

기계적 데이터

항목 치수 단위
도트 매트릭스 128 × 128 dots
모듈 치수 25.9 x 30.1 x 1.26 mm
활성 영역 20.076 x 20.076 mm
도트 크기 0.137 x 0.137 mm
도트 피치 0.157 x 0.157 mm
디스플레이 모드 패시브 매트릭스 (Passive Matrix)
디스플레이 색 Monochrome
Drive Duty 1/128 Duty
IC SH1107
인터페이스 6800,8080,4-wire SPI,I2C
크기 1.12 인치

절대 최대 정격값

Parameter 기호 최소값 최대값 단위
Supply Voltage for Logic VDD -0.3 3.6 V
Supply Voltage for Display VPP -0.3 17.0 V
작동 온도 TOP -40 +80 °C
보관 온도 TSTG -40 +85 °C

전기적 특성

항목 기호 조건 최소값 대표값 최대값 단위
Supply Voltage for Logic  VDD 1.65 3.0 3.3 V
Supply Voltage for Display  VPP 7.0 12.0 12.5 V
Input High Volt. VIH 0.8×VDD VDD V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH 0.8×VDD VDD V
Output Low Volt. VOL 0 0.2×VDD V
50% Check Board operating Current IPP VPP=12V 15.0 25.0 mA

인터페이스 핀 기능

No. 기호 기능
1 VPP This is the most positive voltage supply pad of the chip.
It should be supplied externally.
2 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
3 VDD Power supply for logic and input.
4 NC Not connected.
5 IM1 These are the MPU interface mode select pads.
  8080 I2C 6800 4SPI
IM1 1 1 0 0
IM2 1 0 1 0
6 IM2
7 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 15.625uA.
8 CS This pad is the chip select input. When CS = “L”, then the chip select becomes active, and data/command I/O is enabled.
9 RES This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
11 WR This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When WR = “H”: Read. When WR  = “L”: Write.
12 E/RD This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
13~20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA). At this time, D2 to D7 are set to high impedance.
21 GND Ground
22 NC Not connected.

관련 제품

go top
close

우리는 귀하의 프라이버시를 소중히 여깁니다

"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책

우리는 귀하의 프라이버시를 소중히 여깁니다

Winstar와 일부 제3자는 www.winstar.com.tw에서 쿠키를 사용합니다. 쿠키의 종류, 목적 및 관련된 제3자에 대한 자세한 내용은 아래 및 당사의 쿠키 정책에 설명되어 있습니다. 웹사이트에서 최상의 경험을 얻으려면 "모두 허용"을 클릭하여 당사의 쿠키 사용에 동의해 주세요. 또한 선호 설정을 하거나 필수 쿠키를 제외한 쿠키를 거부할 수도 있습니다.

동의 설정 관리

항상 활성화
필수 쿠키

이 쿠키는 웹사이트를 탐색하고 개인 정보 설정, 로그인 또는 양식 작성과 같은 기능을 사용할 수 있도록 하는 데 필수적입니다.

분석 쿠키

“통계 쿠키”라고도 알려진 이러한 쿠키는 웹사이트 사용에 대한 정보를 수집합니다. 예를 들어 어떤 페이지를 방문했는지, 어떤 링크를 클릭했는지와 같은 정보입니다. 자세한 내용을 확인하세요.