OLED Gráfico COG SH1107 SPI 128x128 de 1,12 polegadas - WEO128128G

OLED Gráfico COG SH1107 SPI 128x128 de 1,12 polegadas

Model No. WEO128128G

►Tipo: Gráfico
►Estrutura: COG
►Tamanho: 1.12"
►Matriz de pontos 128 x 128
►IC：SH1107
►Alimentação 3V
►1/128 duty
►Interface: 6800,8080,4-wire SPI,I2C
►Display Color: Branco / Amarelo

PDF DOWNLOAD

DEMO CODE ADD TO INQUIRY

PREV. BACK to LIST NEXT

Descrição

DRAWING

1.12 inch OLED, 128x128 SPI OLED Display - WEO128128G

Data source ref:WEO128128GWAP3N00000

SPECIFICATIONS

Função do pino de interface

No.

Símbolo

Função

VPP

This is the most positive voltage supply pad of the chip.
It should be supplied externally.

VCOMH

This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.

VDD

Power supply for logic and input.

Not connected.

IM1

These are the MPU interface mode select pads.

	8080	I2C	6800	4SPI
IM1	1	1	0	0
IM2	1	0	1	0

IM2

IREF

This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 15.625mA.

This pad is the chip select input. When CS = “L”, then the chip select becomes active, and data/command I/O is enabled.

RES

This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.

This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.

This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When WR = “H”: Read. When WR = “L”: Write.

E/RD

This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.

13~20

D0~D7

This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA). At this time, D2 to D7 are set to high impedance.

GND

Ground

Not connected.

Dados Mecânicos

Item	Dimensão	Unidade
Matriz de pontos	128 × 128	ponto
Dimensão do módulo	25.9 x 30.1 x 1.26	mm
Área ativa	20.076 x 20.076	mm
Tamanho do ponto	0.137 x 0.137	mm
Distância entre pontos	0.157 x 0.157	mm
Modo de exibição	Passive Matrix
Cor de exibição	Monochrome
Drive Duty	1/128 Duty
IC	SH1107
Interface	6800,8080,4-wire SPI,I2C
Tamanho	1.12 polegadas

Classificações Máximas Absolutas

Parameter	Símbolo	Valor Min	Valor Máximo	Unidade
Supply Voltage for Logic	VDD	-0.3	3.6	V
Supply Voltage for Display	VPP	-0.3	17.0	V
Temperatura de operação	TOP	-40	+80	°C
Temperatura de armazenamento	TSTG	-40	+85	°C

Características Eletrônicas

Item	Símbolo	Condição	Valor Min	Valor Típico	Valor Máximo	Unidade
Supply Voltage for Logic	VDD	－	1.65	3.0	3.3	V
Supply Voltage for Display	VPP	－	7.0	12.0	12.5	V
Input High Volt.	VIH	－	0.8×VDD	－	VDD	V
Input Low Volt.	VIL	－	0	－	0.2×VDD	V
Output High Volt.	VOH	－	0.8×VDD	－	VDD	V
Output Low Volt.	VOL	－	0	－	0.2×VDD	V
50% Check Board operating Current	IPP	VPP=12V	－	15.0	25.0	mA