Strona główna Produkty Wyświetlacz OLED Graficzne Wyświetlacz OLED WEO128128G

1.12", 128x128, SPI Wyświetlacz OLED graficzne

Numer modelu WEO128128G

►Typ: graficzny
►Struktura: COG
►Rozmiar: 1.12"
►128 x 128 matryca punktowa
►IC:SH1107
►zasilanie 3V
►wypełnienie 1/128
►interfejs: 6800,8080,4-wire SPI,I2C
►Kolor wyświetlacza: biały / żółto

Opis

Rysunek

1.12 inch OLED, 128x128 SPI OLED Display - WEO128128G
Data source ref:WEO128128GWAP3N00000

Specyfikacja

Dane mechaniczne

Rzecz Wymiar Jednostka
Matryca punktowa 128 × 128 dots
Wymiary modułu 25.9 x 30.1 x 1.26 mm
Obszar aktywny 20.076 x 20.076 mm
Wielkość piksela 0.137 x 0.137 mm
Raster pomiędzy pikselami 0.157 x 0.157 mm
Tryb wyświetlania matryca
Kolor wyświetlacza Monochromatyczny
Drive Duty 1/128 Duty
IC SH1107
Interfejs 6800,8080,4-wire SPI,I2C
Rozmiar (Przekątna) 1.12 calowy

Bezwzględne oceny maksymalne

Parameter Symbol Minimalna wartość Maksymalna wartość Jednostka
Supply Voltage for Logic VDD -0.3 3.6 V
Supply Voltage for Display VPP -0.3 17.0 V
Temperatura pracy TOP -40 +80 °C
Temperatura przechowywania TSTG -40 +85 °C

Parametry elektryczne

Rzecz Symbol Stan Minimalna wartość Typowa wartość Maksymalna wartość Jednostka
Supply Voltage for Logic  VDD 1.65 3.0 3.3 V
Supply Voltage for Display  VPP 7.0 12.0 12.5 V
Input High Volt. VIH 0.8×VDD VDD V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH 0.8×VDD VDD V
Output Low Volt. VOL 0 0.2×VDD V
50% Check Board operating Current IPP VPP=12V 15.0 25.0 mA

Funkcja pinów interfejsu

No. Symbol Funkcja
1 VPP This is the most positive voltage supply pad of the chip.
It should be supplied externally.
2 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
3 VDD Power supply for logic and input.
4 NC Not connected.
5 IM1 These are the MPU interface mode select pads.
  8080 I2C 6800 4SPI
IM1 1 1 0 0
IM2 1 0 1 0
6 IM2
7 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 15.625uA.
8 CS This pad is the chip select input. When CS = “L”, then the chip select becomes active, and data/command I/O is enabled.
9 RES This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
11 WR This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When WR = “H”: Read. When WR  = “L”: Write.
12 E/RD This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
13~20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA). At this time, D2 to D7 are set to high impedance.
21 GND Ground
22 NC Not connected.

Produkty powiązane

go top
close

Cenimy twoją prywatność

Klikając „Zezwól na wszystkie pliki cookie”, zgadzasz się na przechowywanie plików cookie na swoim urządzeniu w celu usprawnienia nawigacji po witrynie, analizy korzystania z witryny oraz wspierania naszych działań marketingowych i dotyczących wydajności. Więcej informacji na ten temat znajdziesz w naszej polityce. Polityka prywatności

Cenimy twoją prywatność

Winstar i niektóre strony trzecie używają plików cookie na stronie www.winstar.com.tw. Szczegóły dotyczące rodzajów plików cookie, ich celu oraz zaangażowanych stron trzecich są opisane poniżej i w naszej Polityce plików cookie. Kliknij „Zezwól na wszystko”, aby wyrazić zgodę na korzystanie z plików cookie i uzyskać najlepsze możliwe wrażenia na naszych stronach internetowych. Możesz także ustawić preferencje lub odrzucić pliki cookie (z wyjątkiem niezbędnych plików cookie).

Zarządzaj preferencjami zgody

Zawsze aktywne
Niezbędne pliki cookie

Te ciasteczka są niezbędne, aby umożliwić Ci poruszanie się po stronie internetowej i korzystanie z jej funkcji, takich jak ustawianie preferencji prywatności, logowanie się lub wypełnianie formularzy.

Ciasteczka analityczne

Te pliki cookie, znane również jako „ciasteczka statystyczne”, zbierają informacje o tym, jak korzystasz z witryny, takie jak które strony odwiedziłeś i które linki kliknąłeś. Zobacz szczegóły.