我们重视您的隐私
通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。
型号 WEO012832M-CTP
►类型:图形OLED
►结构:COG
►尺寸:0.91寸
►适用于穿载装置
►128 x 32 点阵
►IC:SSD7317
►3V电源电压
►1/32 duty
►接口:SPI/I2C
►In Cell 内嵌式触控面板
►发光颜色: 白色 / 黄色
WEO012832M-CTP型号是一款0.91吋COG绘图型OLED显示器,采用In-Cell内嵌式电容触控面板,分辨率为128x32像素。模块内建SSD7317 TDDI IC,此款IC采用TDDI IC为触控与面板整合驱动IC (Touch with Display Driver),将面板驱动IC和触控面板IC整合成一颗芯片的触控技术,WEO012832M-CTP 型号PMOLED模块采用内嵌式 (In-Cell ) 触控技术,主要可应用于穿戴装置、智能家电和智能医疗保健装置等产品应用。
WEO012832M-CTP型号采用In-Cell 内嵌式触控面板技术,支持4线SPI和I2C接口,并支持四个区域触控和单一方向左右滑动。逻辑电源电压(VDD)为1.65V~3.5V,typical值3.3V,50%显示画面耗电流4mA @8.5V VCC (typical 值),驱动方式1/32。此模块工作温度范围为-40℃~+80℃;储存温度范围为-40℃~+85℃。
WEO012832M-CTP 型号 OLED 模块具有 10,000:1 的高对比度度,可呈现更鲜艳、更深的黑色以及更明亮的白色。 这样可以提高影像质量、更清晰的细节并提高可读性。
Data source ref: WEO012832MWAP3J00000
项目 | 规格说明 | 单位 |
---|---|---|
点阵(分辨率) | 128 × 32 Dots | - |
模块尺寸 | 30.0 × 11.5 × 1.41 | mm |
有效区域 | 22.38 × 5.58 | mm |
像素大小 | 0.155 × 0.155 | mm |
像素间距 | 0.175 × 0.175 | mm |
显示模式 | 被动矩阵 | |
显示颜色 | 单色 | |
驱动方式 | 1/32 Duty | |
IC | SSD7317 | |
OLED 接口 | 4线 SPI,I2C | |
CTP 接口 | SPI,I2C | |
手势 | 4-key 和 1-D slide | |
尺寸 | 0.91 寸 |
参数 | 符号 | 最小值 | 最大值 | 单位 |
---|---|---|---|---|
逻辑电源电压 | VDD | 0 | 4.0 | V |
逻辑电源电压 | VCI | 0 | 4.0 | V |
显示电源电压 | VCC | 0 | 19 | V |
工作温度 | TOP | -40 | +80 | °C |
储存温度 | TSTG | -40 | +85 | °C |
项目 | 符号 | 条件 | 最小值 | 典型值 | 最大值 | 单位 |
---|---|---|---|---|---|---|
逻辑电源电压 | VDD | - | 1.65 | 3.3 | 3.5 | V |
触控控制器电源电压 | VCI | - | 3.0 | - | 3.5 | V |
显示电源电压 | VCC | - | 8.0 | 8.5 | 9.0 | V |
输入高准位 | VIH | - | 0.8×VDD | - | - | V |
输入低准位 | VIL | - | - | - | 0.2×VDD | V |
输出高准位 | VOH | - | 0.9×VDD | - | - | V |
输出低准位 | VOL | - | - | - | 0.1×VDD | V |
50%显示画面耗电流 | ICC | VCC =8.5V | - | 4 | 8 | mA |
No. | 符号 | 功能说明 | ||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VCI | Power supply pin for touch analog driving. VCI must be greater than or equal to VDD. | ||||||||||||||||||||
2 | VSS | Ground pin. | ||||||||||||||||||||
3 | VCC | Power Supply for Display. Most positive voltage. Connect to external source. | ||||||||||||||||||||
4 | VSL | This is segment voltage (output low level) reference pin. When external VSL is not used, connect externally to VSS. When external VSL is used, connect with resistor and diode to ground |
||||||||||||||||||||
5 | DCDCEN0 | Enable output pin for external DCDC circuit. NC if not used | ||||||||||||||||||||
6 | DCDCEN1 | Enable input pin for external DCDC circuit. Tie low if not used. | ||||||||||||||||||||
7 | VDD | Power supply pin for core logic operation. | ||||||||||||||||||||
8 | FR | This pin outputs RAM write synchronization signal. It should be kept NC if it is not used. |
||||||||||||||||||||
9 | DCS | This pin is the chip select input connecting to the MCU for display interface. | ||||||||||||||||||||
10 | TCS | This pin is the chip select input connecting to the MCU for touch. | ||||||||||||||||||||
11 | RES# | This pin is the reset signal input for display interface. | ||||||||||||||||||||
12 | TRES | This pin is the reset signal input for touch. | ||||||||||||||||||||
13 | DC | This pin is Data/Command control pin for display interface. In I2C mode, this pin acts as SA0 for slave address selection. |
||||||||||||||||||||
14 | E/RD# | In I2C mode, this pin acts as SA1 for slave address selection. | ||||||||||||||||||||
15 | IRQ | Interrupt signal for touch reporting. | ||||||||||||||||||||
16 | TD0 | Serial Data Input/Output and clock for Touch In SPI mode TD2 serves as SDOUT, TD1 serves as SDIN, and TD0 serves as the serial clock SCLK. In I2C mode TD2 and TD1 should be tied together and serve as SDA and TD0 is the serial clock SCL. External pull up resistors. |
||||||||||||||||||||
17 | TD1 | |||||||||||||||||||||
18 | TD2 | |||||||||||||||||||||
19 | VSS | Ground pin. | ||||||||||||||||||||
20 | D0 | The serial clock input for display interface. | ||||||||||||||||||||
21 | D1 | The serial data input for display interface. | ||||||||||||||||||||
22 | BS1 |
|
||||||||||||||||||||
23 | BS3 | |||||||||||||||||||||
24 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。