我们重视您的隐私
通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。
WEO012864AD为COG结构0.96寸绘图型OLED显示器模块,显示画面由128x64 dots组成。此OLED模块内置ST7315 IC,有8-bit 6800 / 8080、3线/4线 SPI 和 I2C等多种接口可选择。WEO012864AD显示电压 typical value 12V, 逻辑电压 typical value 3V,驱动方式1/64 duty, 50%显示画面耗电流为6 mA@3.0VCC (白色)。WEO012864AD型号是WEO012864D型号的 IC 替代解决方案; 电气特性和PFC引脚定义相同,客户只需调整初始代码。 Winstar 0.96吋 OLED 有许多替代选择,例如 WEO012864C型号内置 SH1106 IC ,WEO012864AC型号内置 SSD1315 IC,以及WEO012864AD型号内置 ST7315 IC 。
WEO012864AD型号适用于智能家居应用、金融POS、Cloud/IoT systems、智能技术设备、能源系统、通信系统、医疗仪器等。模块操作温度范围-40~+80°C;储存温度范围-40~+85°C。
项目 | 规格 | 单位 |
---|---|---|
点阵(分辨率) | 128 x 64 Dots | - |
模块尺寸 | 26.70 x 19.26 x 1.26 | mm |
有效区域 | 21.74 x 10.86 | mm |
点大小 | 0.15 x 0.15 | mm |
点间距 | 0.17 x 0.17 | mm |
显示模式 | 被动矩阵 | |
发光颜色 | 单色 | |
驱动方式 | 1/64 Duty | |
控制器IC | ST7315 | |
接口 | 6800, 8080, SPI, I2C | |
尺寸 | 0.96 寸 |
参数 | 符号 | 最小值 | 最大值 | 单位 |
---|---|---|---|---|
逻辑电源电压 | VDD | -0.3 | 5.5 | V |
显示电源电压 | VOLED | 0 | 18.0 | V |
工作温度 | TOP | -40 | +80 | °C |
储存温度 | TSTG | -40 | +85 | °C |
项目 | 符号 | 条件 | 最小值 | 典型值 | 最大值 | 单位 |
---|---|---|---|---|---|---|
逻辑电源电压 | VDD | - | 2.4 | 3.0 | 5.0 | V |
显示电源电压 | VOLED | - | 7.5 | 12.0 | 16.5 | V |
电荷帮浦稳压器电源电压 | VBAT | - | 3.0 | 3.5 | 5.0 | V |
显示器的电荷帮浦输出电压 (Generated by Internal DC/DC) |
Charge Pump VOLED |
- | 7.0 | 7.5 | - | V |
输入高准位 | VIH | - | 0.8×VDD | - | - | V |
输入低准位 | VIL | - | - | - | 0.2×VDD | V |
输出高准位 | VOH | - | 0.9×VDD | - | - | V |
输出低准位 | VOL | - | - | - | 0.1×VDD | V |
Display 50% Pixel on Operating Current for VOLED (VOLED Supplied Externally) |
IOLED | VOLED=12V | - | 6 | 12 | mA |
Display 50% Pixel on (VOLED Generated by Internal DC/DC) |
IBAT | VBAT=3.5V | - | 15 | 30 | mA |
No. | 符号 | 功能说明 | ||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | N.C. (GND) | The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground. | ||||||||||||||||||||||||
2 | C2N | DC/DC voltage converter. Connect a capacitor between CA1P and CA1N. Connect a capacitor between CA2P and CA2N. |
||||||||||||||||||||||||
3 | C2P | |||||||||||||||||||||||||
4 | C1P | |||||||||||||||||||||||||
5 | C1N | |||||||||||||||||||||||||
6 | VBAT | Analog power for internal booster. If VDD=VABT | ||||||||||||||||||||||||
7 | NC | NC | ||||||||||||||||||||||||
8 | DGND | Digital ground. Connect to GND | ||||||||||||||||||||||||
9 | VDD | Power supply pin for core logic operation. | ||||||||||||||||||||||||
10 | IF0 | These pins select interface operation mode.
|
||||||||||||||||||||||||
11 | IF1 | |||||||||||||||||||||||||
12 | IF2 | |||||||||||||||||||||||||
13 | CSB | Chip select input pin. CSB=“L”: This chip is selected and the MPU interface is active. CSB=“H”: This chip is not selected and the MPU interface is disabled (D[7:0] are high impedance). |
||||||||||||||||||||||||
14 | RSTB | This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation. | ||||||||||||||||||||||||
15 | A0 | It determines whether the access is related to data or command. A0 = "H": Indicates that D[7:0] are display data; A0 = "L": Indicates that D[7:0] are control data. This pin is I2C slave address bit (SA0), when I2C interface is selected. |
||||||||||||||||||||||||
16 | RWR | Read / Write execution control pin. (This pin is only used in parallel interface)
This pin is not used in serial interfaces and should be connected to DGND. |
||||||||||||||||||||||||
17 | ERD | Read / Write execution control pin. (This pin is only used in parallel interface)
This pin is not used in serial interfaces and should be connected to DGND. |
||||||||||||||||||||||||
18~25 | D0~D7 | When using 8-bit parallel interface: 8080 or 6800 mode 8 bit bi-directional data bus. Connect to the data bus of 8-bit microprocessor. When CSB is “H”, D[7:0] are high impedance. When using serial interface : 3-line SPI or 4-line SPI mode D[2:1] : serial input/output data (SDA). D[0] : serial input clock (SCL). D1 to D2 must be connected together (SDA) D[7:3] : fix to “L” by DGND. When using serial interface : I2C interface D[2] : SDA_OUT, serial data and acknowledge output for the I2C interface. D[1] : SDA_IN, serial input data D[0] : SCL, serial input clock . D1 to D2 must be connected together (SDA) D[7:3] : fix to “L” by DGND. |
||||||||||||||||||||||||
26 | IREF | Internal IREF is used, please leave this pin open. | ||||||||||||||||||||||||
27 | VCOMH | VCOMH is the driving voltage for common and segment circuits. | ||||||||||||||||||||||||
28 | VOLED | VOLED is the diving voltage for segment circuit. | ||||||||||||||||||||||||
29 | PGND | Analog ground. Connect to GND | ||||||||||||||||||||||||
30 | NC (GND) |
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground. |
通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。